Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello,
I have a nrf51822 chip that I would like to flash using Segger Flasher in Stand-alone mode. When I am trying to load the program to the chip I get the following...
I'm trying to add DFU service support to my application on an nRF51 development board, using the instructions here: Adding DFU Service support to an application . I'm using...
I am not a native English speaker, I am totally confused with this line of code where I have found in many samples
#define APP_ADV_INTERVAL 300 /**< The advertising interval...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hi,
I have an issue in using GPIOTE_IRQHandler.
Let me give an explanation about our implementaiton.
we have nRF controller which is connected to STM32 controller...
Hi
Is possible to use GAP White-list to restrict connections without the bond manager system ?
Just by save the white-list with pstorage.....
for exemple, first open...
Hi,
I'm using S110 on PCA10028, I have problems with byte receiving on UART and can't make it work.
I can easily send and receive data over terminal using UART. I can...
Hello,
i use notifications with sd_ble_gatts_hvx. If I push a lot of data, are notifications overwritten or do they are fifoed ?
How to do a kind of flow control to...
So I'm just getting started with NRF51822 and BLE in general; I have built a simple prototype with the BLE Nano using Arduino+BLEPeripheral library. I have converted that...
Hello,
I've read that some devices (e.g. Nexus 4 and Nexus 7) notify only about the first adv. packets from connectible peripheral and the only solution is to disable continuous...
Hello
I am working on a proprietary radio protocol while dealing with a problem that I stuck at for 2 days now. I am managing to get the radio stuck in a TX state (NRF_RADIO...
Hi,
I would like to ask a question about the power consumption specified in nRF8001 datasheet:
the graph on page 40 shows that the average current consumption is about ...
uart not accepting my static passkey when i added dfu in my project. using ios app nrftoolbox.
programed soft device s110. programed dfu dual bank example project then uploaded...
hi i am trying to setup a connection with CP2130 with nrf51. i am using nrf6310 kit. i flashed the spi slave example into into nrf51. on nrf51 these are the connection pins...
