I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Hi,
I've the need to write a characteristic value of 65 bytes, from my central device (iPhone/iPad) to a nRF51822 peripheral device, so I was looking at this document for...
Hi, sorry if this is a dumb question. I've just ordered some development kits and maybe that will answer the question, but i'm being a bit impatient!
I want to put an nrf51422...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi all,
In my project ,I use the SPI to communication between nRF51822 and STM32,but I don't know
how does the heart_rate data transmit to BLE stack.
I am confused...
We have a custom nrf15822-AA board flashed with the S110 (6.0.0) and our application. It has a 32khz crystal. It is connect to our (Mac) development systems with a SEGGER...
I use 51422 with ANT function. When I set a command like "sd_ant_channel_unassign", how can I get response from on_ant_evt callback?
I need to do something after ANT unassign...
I have a nRF8002, I use nRFgo Studio to program the board, and Master Control Panel on Windows to check it board values.
I would like to be able to recognize when the nRF8002...
As the network speed is so low that I often cann't access www.nordicsemi.com, especially on weekends.
Could you tell me the reason?
Note:
At the time when I can...
I am successfully communicating through nrf 8001 chip and i using this module. Now i want to write services and characteristic to this module through iPhone after getting...
Hello：
1.
I used connect Master Control Panel and ble_app_cscs services see the following received some data not understand do not understand, here's UUID I did not see...
Hi all,
I have various questions regarding the softdevices, memory management and power consumption of the nrf51822 chips.
The project we are working on will need to...
I am working on nRF24LE1 boards. I am trying to talk between two boards. I have loaded "enhanced_shockburst_ptx_nrf24le1" and "enhanced_shockburst_prx_nrf24le1" on two different...
I saw an ANCS examples in sdk5.1.0(softdevice=6.0.0), and then I put this example to port to sdk4.4.2 (softdevice=5.2.1) and the example worked perfectly. But when I put the...
Hello,
I have set up my project to use the DFU bootloader to upgrade the application. When my application is running it can be sent a command from the central device to...
Hi
Can I read the content of RF register for LE1 by using the SPI of extern MCU?No matter the code of LE1 is encrypted or not.
When set the LE1 to 0dBm,the TX power...
