Hello,
I would like to know if there is official C# source code to perform DFU OTA for a NRF52840 from Windows without Nordic hardware (DK, dongles etc..), using only the...
Using the Nordic NRF54L15 as part of the nRF54L15-PDK(v0.7.0).
I am working on enabling and experimenting with adding mcuboot and enabling DFU support via BLE.
I have...
Hi,
I need to implement BLE central and peripheral roles on nRF52832 using OS. I have seen Nordic hrs FreeRTOS example, but it is peripheral only.
How could both roles...
Hello everyone,
I'm using the Bluetooth Peripheral sample UART and have noticed an issue.
When I perform a lot of sequential pairing requests followed by cancels from...
Hi,
I'm using nRF5340 Audio DK with the audio example code in BIS mode. I would like to set the broadcast name during runtime, and not before compilation. Namely, I want...
Hi.
I try to build the nrf_audio sample as BIS headset with enabled FOTA and NCS2.7.0 and get the following link error for the ipc_radio image:
FAILED: zephyr/zephyr_pre0...
I am setting up a project with nRF Connect SDK and want to be sure I am doing things in the best way.
The project will build different firmwares for multiple models of our...
Hi
1. How to set PWM power-on state to Low level in ncs v2.4.1 2. How to configure the dts file so that the corresponding I/O port is in the low state when PWM is powered...
Hi I am trying to use nrf connect extension on vs code. but it is not loading. it stuck like this even though, I deleted and reinstalled all the extensions.
I am able to...
Hello,
I am after an example for nRF5340 showing how to use RTC to wake up from sleep.
I have a couple of timers running few tasks at regular intervals in a forever loop...
new to nordic and keil need help compiling custom project
currently my main file only works with the nordic 1822 series processor and in your example.
I need to have it...
I cannot find a specification for the SAADC converter's reference accuracy. The product specification indicates it is 0.6V, but beyond that I cannot find anything. Looking...
Can we run our Customised Bluetooth Host Stack on nRF5340.
Please provide us with sample Brinup Code for Bluetooth Controller.. Send HCI Reset and Bringing up the Controller...
We need to retrieve data from an FPGA to the nRF5340, process it with the network and Wi-Fi protocol stacks and then send the data to the nRF7002 for Wi-Fi transmission. We...
Hello, I am wondering - Is it possible to program BL651 Bluetooth 5 with nRF52810 using pca10040 development board with nRF52832 on it and using
BLE HID Keyboard and Mouse...
Hi!
Currently I have the following application requirements:
Use SPI peripheral to communication with FPGA device. ( NRF5340 [ SLAVE ] <---> FPGA [ MASTER ] )
The goal...
i'm trying to read voltage signals from a sensor using internal ADC.When the input is not connected,there will be noise. I use differential input pins like this:
NRF_DRV_SAADC_DEFAULT_CHANNEL_CONFIG_DIFFERENTIAL...
Hi,
i need to store few configuration bytes in non volatile memory. I found out there is settings module that can be enabled in Kconfig GUI (SETTINGS option).
My use is...
Hi,
I have successfully programmed the nRF5340 Audio DK as a gateway device using the Command Line Tools and by using the directives listed in the 'nRF5340 Audio' program...
I'm working on adapting ST's RFAL NFC library for ST25R3916B/X-NUCLEO-NFC08A1 on an nRF5340/DK in order to emulate an NFC tag, and have run into an inconsistency I'm hoping...
I have an application where I need to trigger time critical SPI reads of accelerometer data (sample rate is very crucial and data is fed into a FFT). In my current SDK based...
Hello!
I have added a UART and I2C to the Mesh Sensor Server example and on a custom NRF52840 board everything works fine.
Today I tried to add SPI without success.
...