Hi,
I'm using the nRF52840 with the SoftDevice for BLE. In my system, it's primarily a BLE transceiver controlled via SPI by an external TI MSP430. We're considering implementing...
Hello,
I want to request AGNSS information from nrf cloud services using my nRF9151DK board. As a first step, I flashed the nRF Cloud multi-service application onto my DK...
Hi,
I'm using cdc_acm to create two COM ports on a PC -
// USB support
& zephyr_udc0 {
cdc_acm_uart0: cdc_acm_uart0 {
compatible = "zephyr,cdc-acm-uart" ;
...
Hi,
We are having issues with this part bridging on our via-in-pads. We are using 2oz finished outer layer copper.
Do you have any footprint recommendations for 2oz copper...
Hello,
I'm looking for guidance and understanding of how to properly use the KMU and ITS for secure key storage of a key generated on device.
I see that typical ITS use...
Dear Nordic Support Team How are you? Currently we are looking into how to configure, compile and run a full-fledged NRF5340 project which should provide us with:
- Latest...
Is there a known way to enable MBEDTLS_THREADING_C? I believe my application is running into MbedTLS heap corruption because multiple threads are performing crypto operations...
I am running smp_svr demo on my nrf54l15DK board, and use mcumgr command on my linux.
I could connect to my ble device and echo hello successfully (via peer_name='Zephyr...
Body:
Hello Nordic Team and Community,
I am working on a project using an nRF52840 chip on a custom breakout board . I am not using any pre-made development boards or...
During the testing phase of my device I use the Zephyr (uart) logging module and the Zephyr shell module(CONFIG_SHELL_LOG_BACKEND=y). Shell is mostly disabled, and is enabled...
I followed the migration guide for NCS 2.8.0 here for a custom board with engineering rev B silicon. After doing so I can't flash the board anymore and it gives me this error...
I am developing my product using the desktop app in the NCS SDK. I found that during OTA, it can only upgrade from a lower version to a higher version. This means that when...
I am using Keil v5 and the nRF5 SDK 17.1.0 .
I use this example.(nRF5_SDK_17.1.0_ddde560\examples\ble_peripheral\ble_app_uart\pca10040)
I hope the chip enter system off...
Hello,
We are using the nRF52840_CKAA_R7 package of the nRF52840 on our custom board. The board's USB pin connections are designed based on the nRF9160-DK's nRF52840 reference...
Hi,
I just received my Thingy91x. I followed the onboarding and created a provisioning profile in NRF Cloud. The device did not connect and no logs appeared in Serial terminal...
Hello everyone,
I am trying to execute Nordic Bluetooth ESL tutorial with PAwR. Here, I am able to change the images and handling the state of an LED connected at the Tag...
Hi,
We are encountering an issue where the existing firmware does not run on the chip when powered by a coin cell, even though a 3.3V power supply is available from the...
When I compiled and flashed the Nordic Distance Toolbox example onto two nrf5430dk boards without changing any options, the following message appeared on one of the UART ports...
Hi,
I have the following scenario:
nrf5340
SDK 2.1.1
HFCLK: 32Mhz crystal
LFCLK: square wave of 32768 Hz from an external RTC, range [0 - 1.8] Volts
square wave...
Hi, I am using a custom nrf52832 device. In that device , button is connected with reset pin P0.21. due to reset functionality I am not able get interrupt from button.
how...