Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Does LESC is supported in FreeRTOS?
I init BLE modules in FreeRTOS tasks. After LESC is enabled, system returns error in nrf_crypto_rng_init(). Looks like nrf_stack_info_overflowed...
I'm trying to test out some of the BLE examples on the nRF 51 DK and I'm getting some strange results on the nRF Connect app. When I run the heart rate example, everything...
The modem firmware release notes say
> DTLS supports PSK authentication only
and indeed I can only get PSK to work.
I understand you can't give a timeline, but can you...
Hi All,
We are develop a BLE device which using Proximity profile. And we are modifying the nRF-Toolbox android apk to implement our application. We would like to change...
Hello,
I'm working on a project where I would like to use two nRF52810, one as broadcaster and one as observer. The idea is that the broadcaster sends an advertisement in...
Hello,
I have understanding issues with model inheritance and subscription list (and publish address) sharing.
The Mesh Profile Spec 1.0.1 (chapter 4.2.3) states:
"Within...
Hi,
the mesh profile spec 4.2.1, for the composition data page 0 states: "The size of the state shall not exceed the maximum useful access payload size". The maximum payload...
In SDK5, I found 2 examples : a server GATT in Central & a client GATT in Peripheral...
But in my case my device (nrf52840 board) needs to be :
a peripheral : slave...
Is it possible to send and receive data with the thingy91_at_client_2020-04-29_bc7ade8b?
I found, that this is not supported by AT commands, instead socket libraries for...
Hi everyone,
I have created a custom BLE service with a characteristic and I update the custom value after enabling notifications by calling the ble_cus_custom_value_update...
Hello,
I am integrating saadc example to ble_uart in order to receive analog input signals and send them via ble connection to android application. Low power consumption...
Dear Nordic Team,
We are working on connecting an I2C device to an nRF52840 Dongle . The code we are using is one we've been developing for a few weeks with an nRF52840...
Hi,
For BLE softdevice, I am wondering if it is possible to set connection supervision timeout to infinitive, which means the connection will never be considered lost? ...
Is the process of communication between QSPI and Ext. flash same for QSPI and PSRAM? If not, what could be the procedure?
And how can I communicate with 2 PSRAM using single...
Hello, I want to create a device, that can auto-connect to my phone and only my.
I thought to do it by filtering the MAC address.
But as far as I understand iPhone and...
