I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command： west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
Hi All,
I have to implement an I2C Slave on my nrf52833 BLE project which is currently working (SDK 2.9.2)
I need some confirmation with the following step:
I have...
Hi, I have one service UUID ffe0 that has two characteristics: one of has UUID ffe4 use for "notify" and other one has UUID ffe5 use for "write and read". Now i want to get...
Hello,
I'm having a system consisting of an nRF52 and another processor, with UART between them. If the other processor restarts, nRF's RX line will be pulled low for some...
Hi,
I'm trying to add LESC pairing mechanism to NUS.
Now when I'm doing pairing between nRF52DK and Phone(Android) via normal way, the behavior is what I want. Please...
Hi there,
I am using nRF5_SDK 16 with PCA10056 and Fanstel EV-BT840-V4. I am testing my example with BT-840 module as we will use it for our final product.
First i tried...
SDK: 15.3.0 Sample: ble_app_hids_keyboard Device: EYSHJNZWZ (nRF52832)
I have a question about HID. In the sample program "ble_app_hids_keyboard", the following values are...
SDK: 15.3.0 Sample: ble_app_hids_keyboard Device: EYSHJNZWZ (nRF52832)
I have a question about HID. In the sample program "ble_app_hids_keyboard", "report_map_data" stores...
Hi,
I am measuring a frequency using the ADC (200ksps) and saving the samples into an array. I save 128 samples then move that data to the fft module to check what the signal...
Currently, debug probes - STLink, JLink, OpenOCD, Black Magic Probe, DAPLinkda, etc. connect to a host PC over a USB, serial or network port and then connect to a target ...
I get ACI_BOND_STATUS_FAILED_ENCRYPTION_KEY_SIZE error when I try to bond my nrf8001 peripheral to my iPhoneX. The min and max key sizes are set to 7 and 16.
Any Idea?
Hi,
I'm using the ble_app_uart example as a starting point for my project. Basically I want to program the nRF52 DK to receive data from another device via UART, store them...
Hi Nordic,
I'm working on a project with very limited board space. I'd like to have the option for both SWD and GPIOs to share the same test points on the board. Ideally...
There is an issue in SDK for Thread & Zigbee 4.1.0 release. It does not appear in previous releases. The problem manifests itself as higher current consumption, as shown in...
I flashed nrf52840 usb dongle via SWD and now it can't go to DFU mode even if I press reset.
Green and blue leds are constantly blinking. How can I go to DFU mode in that...
Hi all,
I am developing ADC functions with Mynewt on nrf52 DK PCA10040 board.
The working example code based on SAADC driver nrfx 1.7.0 won't work on nrfx 2.1.0.
Example...
