Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
I have a problem getting fstorage to work with BLE in SDK 14.2.0.
The fstorage example works fine until i change
NRF_SDH_BLE_PERIPHERAL_LINK_COUNT to more than 0
In...
Im am running a nrf528322 board with the s332 softdevice using sdk14.2.
I have implemented flash storage in my program according to the nordic flash_fds example. This works...
Hi Nordic,
I am using SDK 12.3.0 and S130 2.0.1. I have some questions about AFH.
1. Do Nordic stack keep track of some bad channels during communication and would skip...
Hi I am working on pcb design for a long range application with nRF52832. There are lc circuit which is implemented to antenna pins on reference design of nrf52832. I decided...
Hello,
I am trying to develop a custom BLE service. I have been following this tutorial .
I have also looked at this answer to understand the signal path for a WRITE event...
Hi!
I'm using SDK13 (Softdevice version 4.0.2) and I noticed that during an update via DFU bootloader the update of the Softdevice doesn't work.
After the transmission...
Hi Everyone
I have been trying to use nrf52840 on a custom PCB . So far everything is working perfectly except only one single issue which is the controller gets reset and...
I'm new to the NRF series, and for that matter Keil. I have a BT832A which is apparently an NRF52810.
I am able to flash my own code using Keil and and control GPIOs to...
Hello, I am battling with weird problem for 2 days already, need little help if possible, I have tried all remedies and nothing worked so far.
Here is what happened, I followed...
Hello,
I am using SDK5 for my code that builds successfully under Linux, but not under windows.
The error occurs in the SDK, not in the application. I am wondering what...
Hi,
We are trying to optimize the speed at which we send data over BLE UART with the nrf52832. Currently, we are using the ble_nus_data_send() function in a while loop with...
Hi, I am a beginner at this and I want to make a scroll wheel that connect to Android devices as an HID device. I have a custom BLE board from Skylabs (SKB569) with NRF52832...
I'm having trouble using the NRFX SPIM driver on the NRF52810 w/ Softdevice (S112). (SDK15.0.0)
I'm able to initialize but when I go to use nrfx_spim_xfer without the callback...
I'm trying to change the advertising interval for a non connectable BLE device, but this does not seem to vary regardless of the value set.
The code I used is:
#define...
