Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hi,
I have autoprovisioned and autoconfigured my nrf52840 board (provisioning and configuring are made inside the software and not through external app/provisioner).
In...
I have found out some data about flash:
Flash memory Endurance 10 000 Write/erase cycles
My question is UICR's life is same ?
If use ERASEUICR will erase all area (eg...
Hi everyone,
Days ago, I met a problem while trying to implement the DFU function with MESH SDK 2.0.1 and nRF5_SDK_15.0.0 following the quick start guide on different systems...
Hi,
I received my nrf52840 Dongle today. It works quite well using nrfConnect.
However, we need to implement our custom USB bootloader since the default USB bootloader...
Hi,
Since I saw nrf52840 is for "mouse, keyboard" in document, may I ask, is there any hardware supporting to read mouse PS/2 protocol?
If there isn't, any idea to read...
I have an in memory log, built using a custom log backend, which I write to using the NRF_LOG_*() macros.
My implementation of app_error_fault_handler() will do some NRF_LOG_ERROR...
Developing with S112 + Emulated NRF52810 I've run into a road block.
I've set `m_adv_uuids` to the following:
static ble_uuid_t m_adv_uuids[] = { {BLE_UUID_DEVICE_INFORMATION_SERVICE...
Hello everyone,
I am currently working on porting the InvenSense motion driver 6.12 to nrf52.
I am using MPU9250 and nrf52840 pdk.
I've managed to set up the DMP and...
Hello - I have looked through documentation and can't confirm which component on the board is the BLE Module. Could someone follow up with an image of the board to help confirm...
Hi, we are looking at using a FCC pre-certified nRF52832 module such as the murata MBN52832. It would be for a wrist mounted product so will be in close proximity to the body...
Hi there Nordic Semi/ forum,
This is actually my first post here.
I got the NRF52 DK and I want to implement the NFC type 2 ( passive) tag with it that I could both read...
Hi, I am trying to use P0.9(nfc pin) as gpio(input) to read the charging status of a battery from battery charger IC(BQ 24230). the Open-Drain Charging Status Indication of...
hi Nordic engineer
hard platform : N53832DK, 51822DK
software platform nRF52832 use SDK_14.2.0, nRF51822 use SDK 12.3.0
nRF52832 as ecntral and peripheral; nRF51822...
Greetings,
in the system I develop I shall have a task resposible for fetching some amount of data from Flash to RAM. I should mention that the code will be executed from...
Hi,
I try to activate the bonding with the "ble_app_multiperipheral" exemple project I have modified.
It is very strange because I can bond as wanted but only if I set...
