Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
Hello,
I'm trying to make the nrf5340-DK capable of connecting to BLE from multiple devices.
The program is based on: Bluetooth: Bluetooth: Peripheral UART .
I found...
Hi all,
I'm trying to use rtc0 with my custom board build with an nrf9151, but I got a secure fault. I've activated rtc in an overlay file
In my prj.conf
But...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
In order to reduce power consumption , I configured the RX pin of the serial port with an interrupt , and when the device was asleep , it was woken up by an interrupt , and...
Hi I am using an nRF54L15 with an external watch crystal. I have notice that depending on the manufacturer of the crystal I have to use a different internal load capacitor...
Hi,
I just switched over from the nrf52840PDK to the nrf52840DK and I'm running into an issue where the DK board is not firing the NRF_USBD->EVENTCAUSE = Ready event....
Hi,
I'd like to inquire about the recommended configuration for RF conducted emissions testing for the BTLE radio on the nRF52832. As in the reference circuit provided...
I am trying to send more than 255 Bytes of data over I2C so I break it up into 255 byte transfers within a transaction.
I notice a stop/start condition is sent between I2C...
Hi,
I am trying to have two instances of SPI with the same data and clock pins but to two different devices and thus two different select pins.
I have set all the SPI_Enable...
Hi,
The nRF Connect iOS and Android apps provides detailed instructions and functionality for enabling the device boot loader via the iOS/Android] mobile apps. When running...
Hi,
I have a application where the TWI is always reading a sensor in the main task.
When the DFU requiere to reset, frequently the TWI is busy and the current frame is...
I am using nRF5_SDK_15.0.0_a53641a with a nRF52 Development kit. The board is Rev 1.2.4 (the sticker on the bag says nRF6827 and the sticker on the chip says PCA10040). I...
I am struggling to configure all of the options I desire to on the the "ATT-MTU Throughput Example". This is the version provided in the v15.0 of the SDK, with the hex file...
Hi,
I have two nrf52dk devices.
I Want to test the BLE examples which can exchange Bytes of information between each other and display over the UART.
Which examples...
Hi.
My target board has a power switch that is managed by GPIO.
First-time, a user clicks the button, the GPIO is turned on and the system wakes up.
In reset case(Firmware...
I'm troubleshooting my NFCT state machine -- I'm getting a lot of FRAMEDELAYTIMEOUT errors and can't understand why, I'm triggering a TXSTART ASAP... but that's another issue...
Hi there,
Is it possible to feed XC1 or XC2 with an oscillator output rather than using a crystal?
It would make sense for me in terms of application but I cannot see...
hello , I followed this tutorial : devzone.nordicsemi.com/.../wireless-timer-synchronization-among-nrf5-devices
when i put the button 1 i have just a signal of 2 second...
Hello,
I want to use the D-/D+ as general I/O pins but noticed that it's not mentionned "General purpose I/O" in these pins.
Are these pins only available for USB ?...
Hi,
I am working with the examples/peripherals/application template code from SDK 15 against the brf52840-DK board. I am running Linux as my dev environment I am using the...
