Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
I have flashed the Blinky sample onto an nRF52840DK.
The power consumption is extremely high.
I am using an PPKII to in source mode. It is connected to the External Supply...
I am using nRF Cloud to update firmware on nRF9160 based products in the field. They are connected via LTE Cat-M on Telstra in Australia. The problem is that the download...
I need help with this issue. I'm updating the code from SDK 2.4.2 to SDK 2.9.2. I had change the device tree to HWM2 and I'm using sysbuild.
The build log is showing this...
1. nrf51822-qfaa
2. sdk10.0 & sd8.00
Q:
If the MAX_CONN_INTERVAL is set to greater than 200, NRF_ERROR_INVALID_PARAM will be returned when called sd_ble_gap_ppcp_set...
This post had a discussion on using one button but the first reply suggested a buttonless solution. So now I'm not sure if one button dfu is best if same button is used for...
hi,
i am doing a project where i have to exchange strings between nrf52832 as peripheral and andoird smartphone using nrf connect app, in this project data security is a...
Hello!
It's the first time using Nordic devices so i´m doing some SDK examples and trying to merge them. I'm using SEGGER Embedded Studio. Right now i´m using ble_app_blinky...
Hello,
I'm usign nRF52832 IC and SDK5. I want to awake the sleeping MCU by NFC and pair with BLE. In short Pairing device address should be transfer via NFC. There will...
Hi all
i am using SDK15, nrf52832 dev kit and s132 version 5
I followed the below steps:
1)Flash the softdevice
2)Update the generated dfu_public_key in secure_bootloader_dfu...
I am developing a firmware and connected a spi LCD to nRF52840, but I got the max speed only 8 MHZ, in Datasheet is 32 MHZ max.
Which speed of the SPI master is max ? (I...
I'm getting a disconnect reason of 0x3D / BLE_HCI_CONN_TERMINATED_DUE_TO_MIC_FAILURE during a connection attempt. It does not happen for all my phones except one. It appears...
Hello Everyone,
I am a beginner and working on nRF52832 DK using SDK v15 and using keil mdk armv5.25 as a compiler. Currently I am trying to modify an example in the SDK...
Hi,
Quick question: I read in this article on the section "A tough world of lighting controls" it states the following: "Let's say that five messages are spaced 20 ms apart...
Hello everyone ,
We are able to read out ADC values(if i connect battery positive externally on ADC pins). i wanted to know if there is internal connection provided to any...
Hello,
Testing your nRF Connect with a BLE Thermometer. I was able to connect and read data.
Can you help me with one question I have ?
This is part of the log file...
Where to start? Is it possible?
I need to send data between the two chips using 802.15.4.
There is no need to form a network.
I was looking at the Wireless Uart example...
Hello all,
We want to run the example TCP-Client example from IOT SDK.
how should we proceed for the same ?
Which softdevice must we use ?
Thanks and Regards ...
