I'm using the nRF Connect SDK on nrf5340dk and encountering issues when trying to use the non-blocking (asynchronous) I2C API.
i am particularly getting this error - ENOSYS...
Hello everyone
I'm currently trying to make dynamic endpoints on my matter device. I changed the .zap file to accomodate all the possible endpoints (16) with clusters...
Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
I have a NRF9160 design with a TPS63031 regulator providing 3.3v. When my battery gets weak I am seeing spontaneous reboots, likely due to input voltage droop.
I'm experimenting...
When I start program, my program fall down to
__WEAK void app_error_fault_handler(uint32_t id, uint32_t pc, uint32_t info)
{
NRF_LOG_ERROR("Fatal\r\n");
NRF_LOG_FINAL_FLUSH...
Hi
While using 2 nRF51422 dev boards and using the DTM software together with the DTM python example script the python program reports 0% PER even if I cut the antenna...
Hello,
I am using SoftDevice V4.0.3 and nRF52832.
In this code snipet I got the error code 2 when trying to enable SoftDevice :
int main (void)
{
ret_code_t err_code;...
Hi y'all
after having successfully created my own service, similar to the Uart service, I'm now trying to implement security.
As far as I understood, best practice is...
Hi.
I loaded the ble app uart demo and added some bits of code to read some i2c sensors.
I also added a buzzer which buzzes on powerup (simple for loop).
I would leave...
I'd like to (re)set my characteristic's value to Zero. (after my services and characteristics are set)
I tried to search methods that can set value of characteristic when...
Hello,
is it possible to use the RSSI value of the NRF51822 for collision avoidance?
How long does an RSSI measurement take?
I'm trying to implement a discovery protocol...
Hi all! I used PWM module of nRF52832 to create the PWM but i don't know how to update new value to duty_cycle. This is my code. I used Button (Pin 13) to set a new DUTY_CYCLE...
I am trying to set custom value to advertising address. The code snippet is below. I am getting error code 0x10.
static ble_gap_addr_t * p_addr;
uint8_t itr_i;
p_addr...
Hello,
I have a question about stack usage. I use nRF51822 SoC, 12.2 SDK & IAR 7.60.1. I am interested in stack usage. Have you done any estimations? Or may be you have...
We have a BLE application where we need hopping through nodes. I have shown below how it looks like. We don't want mesh network because we don't require node to node communication...
i use nrf52_DK to debug PDM with a digital MIC, and select the P0.09 for the PDM clk, but i have not see any clock signal output, is it right? and i also haven't see the convet...
Say I have 3 records, then I delete them and collect the garbage. If I try to save a new record again, it will be saved with a record ID 4 , but it should be back to 1 after...
