Hi,
I am trying to program the custom nRF9160 board using SEGGER JLink/SWD programmer , For same of the boards when connected to custom board and trying to select the device...
Hello,
we are using a nRF5340 with NCS 2.9 and want to signalize a
UART_LINE_CTRL_BREAK
on USB CDC_ACM to the PC.
Is there a direct way to do this?
Many thanks in...
I am analyzing the power consumption of a custom board with an nRF52833 BLE SOC and nRF21540 FEM for different BLE parameters. In one of my experiments I vary the amounts...
Is there a straightforward way to output the frequency of the 32.768kHz crystal oscillator to a GPIO pin? The motive for this request is to verify the crystal frequency without...
Hello,
I'm developing for nRF54L15 the application with the NSIB + MCUBoot. I have a problem with fprotect in mcuboot returning EINVAL error. That happens due to limitation...
Hi all,
do different settings of SAADC RESOLUTION register affect Conversion Time t CONV ? I cannot find any dependency - the only value given for t CONV is 2 µs typ (7...
My product has nrf52840 with usb mass storage configured using 8MB QSPI flash (same chip as the nrf52840dk - MX25R64)
I would like to allow users to upgrade firmware by...
I have the PPK measuring a custom nRF52-based board. The board consists of the nRF52, a I2C sensor, and bunch of caps (210uF worth). We built a custom board to do current...
We highly anticipate it will but wanted to ask here before we might ask Nordic Support to confirm that the nRF52840 will make use of the ARM TrustZone CryptoCell to provide...
I'm looking to design power management circuit for a 3.7V Li rechargeable battery powered wearable sensor design. Any such reference design would be greatly helpful!
Thank...
I'm developing a device that's supposed to establish an encrypted connection with an Android device and I've gotten PM_CONN_SEC_ERROR_PIN_OR_KEY_MISSING during connecting...
I have the Type 4 Tag sample application running and I can read and write the tag without any problems.
I'm getting a little confused reading through the sample application...
Hello,
I am working with the GPIO tasks and events feature on my nRF52832 DK. And I noticed some strange behaviour. I want that two Pins will toggle if some timer events...
Hi,
Please help me with the following theoretical situation:
I have a NRF52832 running HID profile, mostly sleeping.
From time to time, an external interrupt occur (GPIO...
Hi,
I am trying to get the data written from a central (a smartphone in my case) to one of the characteristic of my peripheral using write request. The problem is that...
Dear developers,
We had a working application with SDK11 SD2.0.1 that we have migrated to SDK12 SD3.0.0. With SDK11 we could successfully bond to multiple peripherals and...
Hi. I use the nRF51882 and Arduino ide for developing. My main goal is turn on and off the Led thru the Bluetooth interface. But when I use the UART service for it I have...
I am seemingly haunted by spurious 'soft resets' I cannot seem to find a good explanation.
I have an application that is to be dormant until activated. When waking up I...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
Hi, Nordic
I download SDK13.0.0-1.alpha_055eef3, open project
\gzll\experimental\gzp_dynamic_pairing\device\pca10040\blank\arm5_no_packs\gzll_dynamic_pairing_device_pca10040...
Is there any example of changing the default mtu size of 23 to a bigger value?
We tried increasing the att_mtu to 512, and reserved more ram for the softdevice, but still...
