I have a custom nRF52832 board with outputs on P0.07 P0.08 P0.09 P0.10 and I want to write to them. 7&8 are working ok but 9&10 are not.
Let me emphasise THE BOARD IS WORKING...
Dear Nordic and community,
I am currently in pre-production phase of designing a PCB based on the NRF9151, and I am a bit confused by the Hardware Device Guidelines, which...
Hi Nordic engineer
I am evaluating a project based on nRF52840 and there is a question need to be confirm before schematic design start.
Due to limitation of power resource...
Hello everyone,
I'm trying to set up the Wifi stack on the nRF7002 and use it with MicroPython, but encountering a lot of difficulty with it. I cropped up a network_wlan...
Hi all,
I have a custom board build with an nRF9151. I'm able to connect on int with USB/UART, I can send and receive AT command. Right now I'd like to send certificat to...
Hello, I'm developing a BLE Central application using the nRF52 SDK. The central connects to multiple peripheral devices (nRF52832), each sending 6-byte ADXL345 accelerometer...
I'm having trouble getting the I2C interface working on our nRF54L15-based prototypes. The initial config write to the device fails; specifically, in the twim driver (i2c_nrfx_twim...
Hi, I have problem with using example codes. I want to add GPIO control to ble_app_uart example. Adding gpio_config() function taken from app_timer_tutorial blocks program...
I'm using NRF52832 SoC and IAR
I've to read data from ADC using SPI. ADC will generate interrupt every 4ms indicating data ready. I've configured GPIOTE to sense the ADC...
A couple of power consumptions Q's for this basic scenario: RTC used via PPI to infrequently sample from ADC and trigger SPI read from external sensor source.
Questions...
Hello,
I need a support for BMD-300 BLE module.
We can flash the BLE module and we can connect it with mobile application via Blue-Tooth.
But when we flash BLE for...
Hi,
I'm using nRF51822 in my senior project (some kind of BLE wearable device).
I'm trying to call my function inside the ble_evt_dispatch() function but it doesn't...
SPI Slave configuration On nRF52
Hi,
I am trying to configure the SPI slave peripheral for interrupt based communicaton with a SPI master
In previous work with ARM...
Hi,
Can any one tell me about all the security features provided by nrf51822 s110 for secure communication?
Share me some example that implement encryption durring communication...
I have a problem with bonding with a static passkey. I have some sensors, which have a static passkey hardcoded in them. If I want to bond with them, I have to provide this...
Hi, I'm new with BLE applications and I'm designing a wearable.
This wearable will be powered with a CR2032 coin cell battery and I'm wondering if you recommend to use some...
Hello
I have a problem with the power of my modules nRF24L01
while awaiting the arrival of data consumption varies between 15mA and 20mA , I am feeding with 9V batteries...
Hi!
I'm using the RNG to encrypt data that I must send via SPI to another module. I'm using the function "sd_rand_application_vector_get", because I'm working with Soft...
Hello,
I'm just getting started with my nRF52832 and I am still trying to get the first example of the tutorial page running ( Getting started with nRF5 DK .
I did everything...
Hello,
I am doing a project that involves getting data from 2 PTX nodes from the slaves via ESB and sending the data obtained to my android phone via BLE. I am doing so by...
Hi,
We have created a new button events for our application in which it will record total time/ticks that the button is presses.
When you press button for 3-4 sec BLE...
