Hello Nordic team, For the ( POC), I configured ADC channel 1 and interfaced a potentiometer to pin P1.14. The ADC was set up accordingly to read raw value from the potentiometer...
Hello, I have been going through the DFU and FOTA lesson in the Nordic intermediate course. I see that there is a FOTA support for a scenario in which we want to update a...
Hi
I need to sync a PC with a BLE board. Fixed delay is not a problem, but jitter should be max +/- 1 ms.
Our competitors have solved this issue some how.
As we all...
Hello. Right now, I am connecting an external flash using SPI. The external flash is used for firmware updates. I'm trying to launch sQSPI to access the external flash. I...
Hello, I would like to ask if the latest SDK version supports power management on the FLPR core of the nRF54L15. According to this article, the power consumption is quite...
Hello Nordic Team,
I am reaching out to ask for some advice and/or guidance on how I may debug code that:
1. Is initialized and runs BEFORE main
2. Is part of the zephyr...
I want to test RF during production but I do not have any GPIO or UART points on my DUT so I don't want to run the DTM. Can anyone tell me what problems there are with this...
Hi:
I reference rate meter program：
“nRF5_SDK_11.0.0_89a8197\examples\ble_peripheral\ble_app_hrs\pca10040\s132_with_dfu”.
After function "device_manager_init"，I handle...
HI,
I am now trying to use nrf51_iot_sdk_0.8.0_f1f6187. And I have run example application in nrf51 iot sdk on nrf51-dk board. It works fine.
Now I want to develop on...
I want to send a service changed indicate after upgrading app by dfu.I know dfu already so that,but i don't know that how dfu do that.
there is service_change_indicate...
I used to able to get the blinky example in SDK11 to work. But for some unknown reason I couldn't scan my device using Nordic master control panel. The LED1 will be turned...
Can the nRF52 output the 32.768kHz clock on a GPIO. If so, do I need the 32.768kHz xtal, or can I output the generated clock from the 32MHz xtal? I need this clock to sync...
Hi
Yesterday I downloaded the new SDK12 and checked what changes could be relevant for my ongoing/next projects.
One remarkable thing was the fact that almost any peer...
Hello,
I'm trying to upgrade the application on my board via OTA DFU but it seems to fail if the app file is greater than 64KB:
DFU fails with my app which is 70kB and...
Hello!
I want to connect the MCP9808 with the nrf52832. Therefor I use i2C.
My example on the nrf52832 is the:
<nRF5_SDK_v11_0_0 folder>\examples\ble_peripheral\experimental_ble_app_eddystone...
Hi , I am using nRF51822 as a ble_peripheral to send the sensor data to the phone. I already add a characteristic with the property of notify , and it could work when using...
Hello,
I've been working with the SPI Slave on a nRF51-DK for several days. I am using the nRF51-DK (PCA10028), S130 v1.0.0 and SDK v10.0.0. First, I set up a RX and TX...
D:\nRF51822\mergehex.exe --merge D:\nRF51822\s110_nrf51822_7.0.0_softdevice.hex _build\ble_app_hrs_s110_xxaa.hex --output hrs.hex
I am doing it.But one of the files to...
hi i am working on nRF51822 chip, trying to flash code using keil IDE through STLink debugger. which i have attached image . while flashing the code it is showing Flash is...
