Hi,
we have ESB PTX and PRX couple from nRF54H20 nRF54H20DK (rev. 0.9.1), SDK: v2.9.0-nRF54H20-rc2 and the same Toolchain, IDE: VSCode + nRF Connect plugin build for CPURAD...
We are currently developing a project using the nRF52832 as the microcontroller, Segger Embedded Studio version 5.42a as the IDE, and the nRF5 SDK 17.0.2. We began by creating...
Hi.
After migration from SDK2.7.0 to SDK2.9.0 I have issues with power mangement. CONFIG_PM_DEVICE_RUNTIME=y, which I used, causes that twi driver doesn't start. I try to...
Hi Community
Greetings, I bought nrf9151 DK module looking at the features, power consumption & size but the fact that NB IOT has a communication rate of 15mins once in...
Hello everyone.
I am developing a custom board using the nRF9160. I tried using the RAM power-down library based on the Power optimization recommendations page of the nRF...
Since the nRF9160 reserved pins are never used, Is there any issue leaving them out of the footprint?
I would place copper keepouts under the reserved pin areas to ensure...
Is it possible to get to port of an UDP socket (ephemeral, offloaded to modem) with NCS 2.9.0 and mfw 2.0.2?
I tried "getsockname" and get "errno 95 (Operation not supported...
I have 2 nrf51-dk with softdevice 130 (one as central, and the other as peripheral), i use sdk v.10.
I have read and follow central tutorial , and all works.
Now, I...
hi,
i want to use 51822 timer counter to capture external pulses,how can i config the capture task?
in the nRF51 Series Reference Manual, it is say
The TIMER implements...
Hi All,
We have been developing device with pca10028 evaluation board and in the process we use also few other custom boards with nrf51822. We use IAR. The device system...
Is there any recommended value for PSTORAGE_MIN_BLOCK_SIZE or is it completely system determined. The commends in pstorage_platform.h are somewhat unclear.
If I only require...
Hello.
I want to migrate function of "sd_ble_gatts_value_set" to nRF52 from nRF51.
I use nRF52832 ,S132 and PCA10040.
I saw documentations about the function.
infocenter...
Hi. I'm using PCA10028, SDK10.0.0, S130.
I want to go to nrf_drv_uart_uninit(); right after sending data.
in order to save current consumption.
So I made source code...
Hi.
I'm using nRF51822, SDK10.0.0, S130.
Hex files : Soft device, Application, bootloader.
I want to download at once.
How can I combine Hex files to make them 1 file...
I'm trying to piece together how to be able to get this migration to work OTA via DFU. I was told by Nordic that all you need is to .zip SD8 + Boot(SDK10) and DFU both to...
I'm using:
nRF51422
SDK 7.1.0
Softdevice S310 2.0.1
nrfjprog.exe v 8.3.0
JLinkARM.dll v 5.10m
If I use the Segger with nrfjprog.exe to upload the softdevice...
I am a bit confused about what happens to ACK_PLD when ack payload packets are lost. I am assuming that in case of ack payload packet loss MAX_RT bit in STATUS is set.
...
Hello,
i have a nRF51 DK 1 and the Dongle to test and try some BLE applications.
Now i want to test how long does it take to establish and close a simple connection.
...
Hello,everyone,I encountered a confusing problem.
My device is nrf51822. I want to test whether the communication between two equipments is normal . So I choose one as central...
I am using a nrf51822 based tag and Android official SDK to implement my custom app. I perform the following steps:
1. Scan
2. Connect
3. Discover services
4. Write...
What CRC type is used for the crc calculation with the function
uint16_t crc16_compute (const uint8_t * p_data, uint32_t size, const uint16_t * p_crc )
of the nRf52 SDK...
Hi
I have a prototype of a board that uses a nNF52832 to communicate over Bluetooth, the board has some buttons intended for user input.
As the board size is little...