Hello,
Is the nrf54 family's I2C peripheral compatible with I3C? I need to communicate with several I3C sensors on the same bus.
If yes, is the software support only...
I'm using the nRF Connect SDK on nrf5340dk and encountering issues when trying to use the non-blocking (asynchronous) I2C API.
i am particularly getting this error - ENOSYS...
Hello everyone
I'm currently trying to make dynamic endpoints on my matter device. I changed the .zap file to accomodate all the possible endpoints (16) with clusters...
Hi community,
I have a similar custom board as Thingy53, which has the nrf21540 module on board.
my purpose is to turn on the nrf21540 and do the reconnection, when...
Hi!
With the release of NCS 3.0.1, the required SEGGER JLink version to v8.18. pynrfjrprog is bundled with SEGGER JLink v7.94. From your website, it seems nrfjprog, being...
Hello,
Over the past three days (up until today), we've observed inaccurate behavior in the Message Routing Service. Specifically, we shut down our destination service during...
Hi,
I use the nRF54L15-DK flash fimware (.hex) with "nRF Connect for Desktop - Programmer" success.
And I view the schematic, discovered the DK board have flash memory...
When I'm single stepping my nRF52 application in Keil with a BLE connection I always get the softdevice_fault_handler called.
I'm using SD 132, v2.0.0 and the the parameters...
What is the maximum clk frequency that can be output on a gpio for the nRF52832 ? I want the nRF52832 to output a clk signal on any of the gpios to an external module, and...
Can anyone please suggest a simple example on initializing SAADC Driver on one pin and do a simple blocking ADC read?
Sorry for a very broad question - but rather to ask...
I'm using the nRF52 Dev board and set the --rbp ALL option while using nrfjprog. It worked fine, and I am able to do OTA updates as I was testing the bootloader example. But...
Hi
I'm doing one project that is taking data from uart and send to mobile app. I'm facing one issue that is when I connected to peripheral it connected and take data from...
I'm looking for some options to extend the PCA10028 with a keybord and a numpad. This would give great options to play around with passkey topics.
As the PCA10028 supports...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Hello,
I am trying the ANT-OTA DFU Update using an ANT Stick and the nr51422 pca 10028 board. The ANT Updater shows that the Image Upload is completed. I am uploading the...
Hi,
I there a way that I can detect if a sections of my code has been interrupted by the Softdevice? I have some time critical code (bit banging a communication protocol...
Hi All,
I am using the nrf51422 and softdevice S310 to send out ANT+ and BT Smart in my project.
I use RTC1->Counter in order to get a timestamp for an interrupt from...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Hi,
I am trying to run an example project which includes a softdevice using Keil uVision on nrf51822xxAA. What should I change in Options for Target? Especially what should...
Hi,
If I connect a peripheral and establish a bonding with MITM the connection security changes to mode 1 / level 3. If the peripheral is disconnected and reconnected the...
Hi,
I am trying to write program follow this structure: first I will enable button using GPIO, then wait botton is pressed, then I read ADC from GPIO pin, if ADC value >...
I'm using a nRF51 beacon as a receiver that produces a pulse when it receives a byte from the transmitter. The code is based on the ble_app_uart example. And I set the connection...
