We have a custom board that I ran through the board_v1_to_v2.py program and then attempted to build under SDK and Toolchain 2.8. When I run it it failed in the CMakeLists...
I am using the Nordic nRF5340 DK to communicate with the ICM-42688-P sensor via SPI. However, the sensor does not respond to the MCU's commands. After observing the SPI clock...
Hello,
I'm just starting with the Power Profile Kit 2. I've read all available documentation but I didn't find any information about the switch SW1 called 'POWER'. There...
Hello,
We are developing a Cellular IoT device based on nRF9160 SiP. Essentially it is a battery powered temperature and humiduty sensor, that sends the measurement data...
Hi,
This is a followup on https://devzone.nordicsemi.com/f/nordic-q-a/119259/synchronisation-between-tx-and-rx-in-connectionless-direction-finding
We now have a synchronised...
Hello, I'm having problems trying to make the MODBUS RTU Client code work on my board.
I'm devoloping with nrf Connect SDK v2.1.0, using Visual Studio Code.
The board...
I am having issues using a keypad to wakeup an nrf52840 and am unclear on if the GPIO sample is relevant if using a kbd_matrix device definition. I would like to use "sys_poweroff...
I have written an application which transfers data from an nrf51822 device to a phone once a day. It currently uses notifications to transfer data, at 20 bytes per notification...
Hi,
I'm learning the BLE protocal these days, I didn't see the protocal say how may packages can send per connection event. Does it mean that the number of packages is...
Hi
Details:
I want To send 40 bytes from GATT Server.My Requirement is same as in this link .I have added the code snippet in this link in my code.When I am sending 20 Bytes...
Hi,
I would like to use the NFC capability of the nRF52 on a custom PCB, and I was wondering if the tag and connector used on the PCA10040 are for sale anywhere, I can't...
We want to design a setup for simultanious translation of up to 3 translators and up to 30 people receiving a translation.
Is it posible to setup a single transmitter, sending...
Hi everyone,
I am trying to monitor and measure the signal strenth variation by varying the positon of the developement kit NRF51 and i tried with the proximity example...
Hi,
I'm using v1.21 nRFgo. As programming 51series ,
(1)I want to know if the program check the hex file before the log dialog shows "programmed successful"?
(2)And...
I run nRF51 with S110 and advertising at least standard battery service. I can see my device in LightBlue scan window but in iOS Settings->Bluetooth it is not picked up. Which...
i am aiming to design a simple data transfer network. i am using 2 DKs. the first one is the central which runs a modified version of MULtilink Central Example and the seond...
I have continued to build upon the Nordic sdk10:gzll_ack_payload example using gcc-4.9-2015q1 on Linux. The differences are:
added UART for debugging (running at 460800...
Hello Nordevzone, so far, to the best of my knowledge, you can send data using API call sd_ble_gatts_hvx() with "notification packet" (quotemarks due to my limited knowledge...
AS i am trying to utilize GCC for more than 32 KB code size,
i use Eclipse which provides more friendly interface.
However, i am still experiencing some setting issues....
Hi,
Details:
I am using nrf sdk 10.0.0 and s130 Softdevice.I am using nrfgo studio for flashing SD,Application Hex files.I am using this nrfgo studio for past three months...
Hi,
I'm developing nRF51 proximity based device using nRF51822 that acts as BLE peripheral. It advertises continuously using connectable indirect mode.
User has Android...
