Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Hi，
I ran into this error:
00> <error> nrf_ble_gq: SD GATT procedure (1) failed on connection handle 0 with error: 0x00000008. 00> 00> <error> app: ERROR 8 [NRF_ERROR_INVALID_STATE...
Hi everyone,
Could someone help me with the following use case?
Task description: I'm working on a firmware update procedure based on the smp_svr project. I'm trying to...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Hello,
I know this question is more related to Zephyr than Nordic, but I wanted to try asking here.
I’m using the SMP service to send files to my device on a LittleFS...
Has anyone tried to plug an R3 shield to the nrf52 DK?
I was about to try, but it looks like the pins don't line up correctly - but then I have no experience with R3 shields...
Hello everyone,
I'm using the nRF52832, i would like to shutdown the timers, so i can enter the low power mode. In the datasheet tasks_shutdown for the timer modules is...
I have an application which receives commands from a co-processor via UART. Some commands are BLE-related such as, e.g. start-scan, stop-scan, connect, etc.
As the UART...
In nrf_drv_adc.c , there are loads of these ASSERT() macro calls:
ASSERT(mp_state == NRF_DRV_STATE_INITIALIZED);
But there is no variable mp_state. This will fail...
Hi! I have asked a question in this topic ( devzone.nordicsemi.com/.../) and now I can send one packet of 20bytes. What I cannot do is sending two packets at the same time...
I have nRF51 Dongle.
I can set it in BOOTLOADER mode and update firmware like:
developer.mbed.org/.../
I see the dongle in Device Manager/Disk drivers like "MBED microcontroller...
Hi all,
i have a little issue.
If i remove the bond information with app Master control panel, my slave cannot connect again with my phone. [Pairing Reject from Nordic_CTS...
I am moving from S110 and SDK 6 point something to S130 and SDK 10. I have my basic BLE code going but am unable to get the SPI back-in-action. I am using gcc and the s130...
I use NRF51822qfaa,s110 v8.0, now I use master TWI to drive the TWI bus chip.
the TWI bus chip Slave Address is 0x48.please see the below program .
question:
1.The...
this is the main program!
#include <stdbool.h>
#include <stdint.h>
#include "nrf_delay.h"
#include "nrf_gpio.h"
#include "boards.h"
const uint8_t leds_list[LEDS_NUMBER...
Hello,
I migrated from SDK 9 to 11 (S132) and i cannot receive anymore custom advertising (from another nRF52)
I receive another devices advertising events so reception...
I'm looking to use this dk for a small project.
Has anyone made or seen a box for the devkit easliy available (.STL) for 3d printing?
And for added coverage, can I just...
The documentation for EVTEN in the manual, showing the RTC Tasks and Events system (Figure 45) led me to believe that if EVTEN for an event is disabled the EVENT will never...
Phone Model: model MX4 from MeiZu china
APP applied: nRF Master
experiment 1:
Here in my hand, when a android phone try to connect to the device which contain the service...
I just now saw the press release for the Primo .
In theory the bootloader should just to be able to be loaded to an existing DevKit either via NRFstudio or the NRFprog...
