There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hello,
My nRF9160 hard faults (i think?) when issuing a command to the modem, specifically this line:
which then calls ncs function:
This leads to I think is...
Hello, I'm trying to run the OpenThread CLI example on the nrf52840 chip of my NRF9160_DK. I've managed to flash the code on the nrf52 and able to see the Zephyr kernel boot...
I have tried various methods from different doccumentations and I couldn't do so. Can you provides some steps to create a west workspace.
Thanks in advance.
In my project, I am planning to use LTE modem and an external flash memory with a file system. I have problems to run code for the non-secure build type. A similar problem...
I've been tinkering for several says to get GNSS working on a Thingy91 with Zephyr.
I've tried the 'location' example and have struggled to register the device on nRFcloud...
Following the instructions to build the sample resulted in an error message ..
Here are the details ... probably something simple but not obvious to me ...
PS C:\ncs>...
Hello Everyone,
I was use Nordic App for Mesh in android to add Telink's chipset into mesh. But after few minutes, telink's device go out Mesh.
I don't know how to add...
Hi,
Iam using "pca10056_s140_ble" secure bootloader example for my project.
FYI. My project gets its new firmware from internet and stores it in BANK1 memory using GSM...
hi Support team,
customer get samples with 9160, but find out they are not able get pin code.
i searched the spec, and at command +CPIN, it is not able to read out the...
Hi,
I've installed ncs manually following this guide: Installing manually — nRF Connect SDK 2.0.99 documentation (nordicsemi.com) and then set the following environment...
Hi,
I have an application using MCUboot (Only for using with serial recovery. No SMP server running in app).
I enable CONFIG_BOOTLOADER_MCUBOOT and parent and child images...
Hi,
I am using nRF5340 DK + NCS v2.0.0 with nrfx backend for SPIM.
For my application I want to trigger a SPIM1 transaction at a fixed interval. To do this, I set up an...
Hello,
I have an issue when trying to use NVS backend for BLE settings with the settings_storage partition in defined external flash region. As we are doing a multi-image...
I am designing a bluetooth module using the soft device S130 + nRF51822. I intend to refer to QDID80592 and 45222 when purchasing DID for bluetooth. When I checked the ICS...
Hi. I am trying to develop a project that use mqtt connection using nrf9160. Currently using thingy:91 for evalutation board. I am using Mobily Network on NB IoT at Saudi...
