Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
HI
This is regarding to create a project which supports below peripheral
1. Uart : To interact with Windows application - Working Configured Successfully
2. I2C: for...
The instructions at https://github.com/NordicSemiconductor/pc-ble-driver do not allow building the driver or the examples on a Windows system. Following the instructions takes...
Hi, I developed a BLE and Zigbee custom product, starting from nRF5 SDK for Thread and Zigbee v3.2.0. On BLE side, it connects with Mobile or Tablet using Pairing with bonding...
Hi,
1. Does nRF52840 CKAA WLCSP support QSPI 32MHz?
2. What should qSPI 32MHz measured CLK waveform look like?
3. Is there a 32M QSPI CLK sample diagram actually measured...
I finally had success in getting a SPIM master running with a single SPI slave (Honeywell sensor running CS 4 on the Arduino R3 header) on my nRF9160DK. But now I need to...
Dear all:
I am developing a ble scanner using RADIO Peripheral.
I have 2 questions to ask
1.When is the END event triggered?, How does the hareware know the packet is...
I received the hardfault in the following image.
The function at the address 0x00028C44 is:
The hardfault did not occur again after resetting. I'm not sure why this...
Hello,
We have a PIC32 controlling the NRF24L01 with some sucess so far.
But sometimes we get the chip in a state that we can't get off.
We still cannot pinpoint the...
Hi Team,
I am developing an application that nordic chips receive data from msp430 chips by the SPI, and send them out.
Nordic can receive the data from the msp430, but...
Hello everyone,
I tried to add the long press event into my bsp_event_handler without success. I get the normal button press event, but the long button press event is not...
Dear Nordic FAE:
Where can I find the nrf52840-CIAA REACH report?
i can not find it by
focenter.nordicsemi.com/index.jsp?topic=%252Fcom.nordic.infocenter.sdk5.v12.2...
Issue:
While trying to initialize and check the viability of an I2C interface using TWIM, my NRF_TWIM_TASK_STOP never triggers NRF_TWIM_EVENT_STOPPED.
Code:
This causes...
Hi,
I have installed the v1.8.0 nrf connect sdk and created a new application using the nrf connect vscode extension based on the ble/throughput example. Created a build...
Dear Nordic Engineer
I would like to know the version of openthread in NCS 1.8.0? And what is the otbr posix version corresponding to rcp firmware? It is reflected in the...
