Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
HI All,
Could you please share the details for the below s on Nordic controller MCU nRF52833-QDAA to receive quotation on BLE_SIG certification,
QDID for Link Layer...
Hi,
I have a custom board running with the nrf52832. To program it I'm using the nrf52DK board with the PCA10040 and the bootloader is based on the one found in examples...
DK : 52840
case :
we make 52840 enter active scan state and know other broadcaster devcice mac,
can we use scan filter policy filter this broadcaster devcice ,and only...
(1) I connected Nordic nRF52810 device to ipad (version: 13.5.1) (ipad uses app for connection). At this time, a pop-up window appears asking if I want to pair the devices...
Good morning. I want to take ADC 12bit/1k sampling input and send uart and bluetooth. uart works fine, but there is a problem with losing data in bluetooth transmission. ...
During testing of various combination of BLE Mesh Provisioning, I found a couple of bugs in dk_prov.c
If you Disable all OOB options for no OOB, it does not work properly...
I'm using nrf_pwr_mgmt_shutdown to shut down the system to wake on interrupt. 17.0.2 SDK and 7.2.0 softdevice. When I step through the code with a debugger, it gets to sd_power_system_off...
My device is powered by an electromagnetic field from the 10 kilovolt line, which cannot deliver much power. When connected to a zigbia network, nrf52840 consumes too much...
I want to receive only 1 byte (Master in Slave out) without sending any bytes using using SPI. However when I monitor the SPI clock it produces 16 clock pulses. Although my...
Hello, How do disable code optimization in SES Nordic Edition when using nRF Connect SDK? I can't find "Options - Code Generation - Optimization Level" as when using nRF5...
Dear Sir,
I am trying to run example with NRF91 DK MQTT simple and I am able to connect with LTE network. as shown in below screenshot.
But as shown in the screen...
Hello, All
I go through datasheet of nRF5284o QFN73 IC. But i can't found which pins are used as uart /spi/i2c/pwm/timer/ I2S in pin description. Because pin assignment...
Hi,
We are using nRF Connect SDK for implementing HSL model for the BLE Mesh network consisting of RGB lights.
On comparison with nRF Mesh SDK, we found that the SDK size...
Running the ADC in continuous mode, but it seems we still have to set NRF_SAADC->TASKS_SAMPLE in a while loop. Shouldn't this not have to be set? In continuous mode we shouldn...
Hello,
Currently, I am having a problem with my BLE application. I am using nRF5_SDK_17.0.2_d674dde version. The BLE can advertise and can be seen by my phone. When my phone...
