I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
The objective is to have a device which constantly advertises some status information - this must be always visible to any Central in range.
The device may connect to at...
I inherited an active project with regrettably little support from the previous developer.
I have been trying to download a copy of the application firmware that I generated...
I try, DFU by USB-SERIAL on NRF52840-DK. I installed SoftDevice S140 V6.1.1 and open_bootloader/pca10056_usb (SDK15.3) Python2.7.16/nrfutil for windows was installed. My DFU...
I am trying to keep an output pin asserted while I jump to the DFU on the 52840.
We have a dead-man switch hooked up to pin 19. I need to hold this pin high while I jump...
So we are using NCPTransport from nrf-util (nordicsemi/thread/tncp.py) to have CoAP connectivity over Thread NCP from Raspberry Pi to other Thread devices. We have a use case...
Hi,
I am trying to install pc-ble-driver-py pypi lib into custom yocto setup. I have created recipes for it which is shown bellow
in python-pc-ble-driver-py.inc
...
Hi. Im working with an application that uses the s110 softdevice and i want to use the s130 to be able to recive advertisereports but when using the s130 Everything stops...
Hey everyone,
I've got an nRF52840 DK on my hands. There's an interesting crash occurring when the return value from ble_nus_data_send() is passed to APP_ERROR_CHECK()....
I am using several Laird BL652 units on a project. They contain a nRF52832. For the most part they are working great, except I have one that only works some of the time and...
I have been trying to use the new GPS example, however, I could not get any location from it yet. It seems that after 30 tries, it stops working (time-out problem). Should...
Hi all,
I'm starting developping code with SES, on an nRF52810 (192kB of Flash), with the BLE stack S112.
Because my project include BLE and custom UUID, I started with...
Hi
I am using the nrf53832 dk.
In the nus example once the data is received from the phone(central) I want to write this data to the flash. I referred to the fstorage...
Hi everyone,
We are currently working on a BLE border router with a module based on nrf52840. The custom board has a MAC + PHY ethernet controller that communicates with...
Hello,
I am using nRF52832 DK PCA10040 v1.2.4, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I have gone through below...
