Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I ran into a couple issues with network core updates on NRF5340 when updating from 3.1.0 to 3.4.0 SDK. Problem 1) Network core updates are not backwards compatible with 3...
Hello, We have a question about the errata workarounds applied in SystemInit() in nRF5 SDK v16.0.0. Our firmware is split into two images: a boot application and a main application...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I have a pin on port 1 of the nrf54l15 that I am bitbanging for a custom tx/rx 2-wire protocol. I have already managed to implement the tx capability and I was hoping...
I'm using nrf9151 and trying to upgrade from ncs3.2 to ncs 3.4. I have two builds, one with log disabled, other with rtt logging enabled. Both builds are working, but I can...
Hi Nordic Team,
I am using MCUBoot with BLE DFU on nRF5340 and I am facing an issue where the DFU process cannot complete due to my application’s custom boot logic.
After...
When I create a new build ciónfiguration in nrf connect I get this Loading and the new configuration is not created itself.
This error is displayed in the VScode.
Could...
Hello, I noticed that the SoftDevice Controller for nrf5340 in nrf Connect SDK 3.1.0 reports a bluetooth version of 6.1 (LMP Version 0x0F), yet the QDID for it ( Q360820)...
Hi,
NCS v3.4.0
BLE peripheral_uart example
nrf54l15 DK with ns config
in the Chinese (double bytes) Windows, need to add encoding="utf-8" in tfm_parse_manifest_list...
Hi,
My central device is running into Bus fault when continuously sending data to multiple connected peripheral device and any of peripheral device got disconneced. Issue...
Hello, our design does not use the USB block of the 52833. In the electrical schematic we have connected VBUS (AD2) to GND and we leave D-(AD4) and D+(AD6) open. Due to a...
I am looking to evaluate Amazon sidewalk on the nrf54L15 dev kit and have also bought both of the Semtech evaluation boards LR1110MB1LCKS and SX1262MB2CAS. The nrf54L15 is...
Hi:
I use sdk ncs3.3.0 and nrf54lm20dk.
Failed to return using AA dfu_target_init.
OTA firmware is zephyr.signed.bin.
I: DFU header I: 3d b8 f3 96 00 00 00 00...
HI
I am currently carrying out secondary development for PAWR based on NCS 3.2.1. I understand that its communication adopts frequency hopping. I would like to ask whether...
