I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
How to calculate the free Ram and Flash after I loaded bootloader + SD + App on a running nRF52840?
I want to know ways to measure during critical RAM load too.
...
Hi, what is the correct way to erase all the connection params of a zigbee router device (not coordinator), and restart to search for a network automatically in production...
Hello,
I am using SDK 15.2.0 ,nrf52840. In my application we are using bluetooth and USB. The application works good. The device advertise and can get into the application...
Hello,
I have SDK v15 and there is not much information in infocenter also about these two functions related to my doubt.
( NRF_PWR_MGMT_SHUTDOWN_GOTO_SYSOFF & nrf_pwr_mgmt_run...
Hello, I'm starting evaluation of the Mesh Light Switch Demo both on DK PCA10056 and on Dongles PCA10059. I 'm using SEGGER IDE and made sure to properly set target in Preprocessor...
Hi , i tried to modify the template example from the sdk 15.3 but im getting an compilation error from " nrf_log_backend_rtt.c"
SEGGER_RTT_Conf.h: No such file or directory...
Trying to up load mqtt_simple sample, however getting bus fault on terminal. have browsed after the same issue here, but don't work after doing git pull ect...
here's...
How to correctly reinitialize the BLE stack when using FreeRTOS?
I can not find in the libraries where the task for the work of the stack under FreeRTOS is created.
Stopping...
We have a connection between our nRF52832 (server) and a tablet (client). We're trying to transmit some data at a rather high throughput. The connection parameters are as...
Hi everyone,
I have a problem with my custom nRF52832 hardware. I soldered my prototype hardware and then I checked if it is correct by checking debugger SW device settings...
Hello,
I'm trying to get as much throughput as possible using the Coded PHY. I noticed that apparently the Data Length Extension feature is not supported together with the...
Sometimes, i found that my firmware still at the old version after update complete, there is no any error.It same happen on use Android-nRF-Toolbox to update firmware.
code...
Hi, I am interfacing external memory chip that is based on SPI protocol with nrf51822. I have to read more than 255 byte via spi in single buffer with 4 byte of command. Even...
Hello,
I am using a custom board with nrf52840 using SDK 15.3 and ICM 20948. I see a lot of twi drivers and its confusing which one to use. I want to read the ICM 20948...
