Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
Hi,
We are developing a device with nRF52840 and mBed-os. We have a bootloader based on SDK 13.0.0.0-1 with softdevice s140 5.0.0-1-alpha.
Changes that has been made to...
Dear nordic,
I need a help from your side i want to create 1 hz(1000 ms time period) frequency pwm using PWM driver. i created upto 30 ms time period but i cant create time...
Hi, I'm using nrf52840 TWI master. Sometimes the I2C bus result as locked in endless loop to retry the start conditions. I see that in this case SDA and SCL are tied low for...
Updating the SoftDevice on the nRF52832 from S132 v2.0.x to S132 v3.0 using the Dual Bank Bootloader from SDK v11.0.0 results in the application not starting up after the...
I am planning to use Open bootloader example as my starting point for adding a bootloader to an application. I donot want Softdevice. Initially I am going to check the dfu...
i am working on ble_app_uart central and peripheral, so basically peripheral will sleep wake up and send advertisement packet to central . Now the issue is if peripheral is...
Hi, My Lord. When I run the example, I use short-name(BLE_ADVDATA_SHORT_NAME) advertising always "Fatal error",It's no use reducing payload.
On the other hand, how to add...
Dear experts..
I'm currently developing and testing nRF52832 application with nRF52-DK.
This are three questions about "actual" advertising packet length on air.
First...
1.HOW TO enable a node relay , friend,proxy or low power ability ?
2.if node A publish a message to a GROUP ADDRESS(0XC001) for node B( subscribeed this group address) ...
I looked at the nRF91_DK_User_Guide and it is very confusing to understand how to set up the board for current measurements. The figure says to solder SB44 and SB45 but the...
Hello,
As of today, April 17th 2019, I am using latest version of SDK and SES. I am using Jlink from nRF51DK and a nRF52832 module bought from ebay.
I tested several examples...
extern void bsd_recoverable_error_handler(uint32_t error) AND
extern void bsd_irrecoverable_error_handler(uint32_t error); Will return various error codes - is there a list...
I'm trying to use the NUS to send data over from NRF52 dev kit to the NRF Connect app. Using Putty for UART works fine. Now I adapted to read out ADC values from 2 ADC ports...
Hi, can someone tell me what chip this is and where I can find the data sheet? Or at least if this is a custom fabrication, what chip from Nordic is it based off of? Thanks...
Hello,
I am using ble_app_uart_c example for my nRF52832 based central application. I would like to modify Tx Power and MODE of my device.
As per datasheet, I should write...
