Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
Hello,
I would like to know if you can point me where to find the electrical characteristic of the module nRF9160. I'm looking for :
- Then maximum current the module...
I work on your new Mesh SDK 3.1.0 and I have some questions for you.
First it is about DFU over Mesh. I think your documentation is very weak. I understand that they are...
Hello Nordic, we use the nrf52 proprietary protocol in the project, it will send 200 data per second, and no ack confirmation, the application data length is 25 or 32 bytes...
SDK 15.2
Segger Embedded Studio Release 4.12 with DEBUG on
Segger Ozone V2.60k
FreeRTOS 10 from SDK (same issue with FreeRTOS 10.1.0 source files and original ported...
What is the exact sequence when reading a characteristic with variable length and authorize required.
When I have a actual data length of 14 I can read with offset = 0 and...
Hi All Team Members,
Using Nordic Development Kit of nrf52832 I am able to write and test basic application using UART and BLE
using this kit I get the following error...
Hello, I use a custom board with nRF51822QFAA, with two buttons (left, right) and uart for printf/debug. The idea of the project is to have the board always sleeping, it wakes...
Hi,
I have a project which need to use two UART interface at the same time.
As well known, there only have one hardware UART interface in nRF51822/nRF52832. If I want...
Hello, DevZone,
I have programmed an nRF52-DK with the unmodified SDK's ble_app_hrs_pca10040_s132 (heart rate monitor) BLE peripheral application. I also have a Power Profiling...
Hi Susheel,
Thank you for your support.
We would like to get your advice related our new design, with the followings:
Assume we need to support besides of the BT5...
Hi,
I am developing one of the my project on custom board, in which I have to configured the two GPIO Pin's as input to sense the those pin and take actions assigned on...
I'm developing a battery powered BLE sensor application where I need some basic guidance on how to implement this:
The sensor action consists of a measurement process where...
Hi there!
I appreciate your work on Nordic SDKs which are getting better and better.
But sometimes SDK setup isn't as quick as it could be.
E.g. for evaluation purposes...
Hi,
I am trying to port the Thingy project (ble_app_thingy_s132_pca20020) to Segger Embedded Studio on a Mac and it proved to be not an easy task, in fact I have hit a...
Dear all, I am building a BLE thermometer based on nRF51422 chip. I need to get certify it and if any of you performed and have the tests results of the below tests, for the...
