Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Good morning,
we are using the Zigbee stack (ZBOSS) on nRF52 devices with Green Power Sink enabled and we are integrating a Green Power door sensor.
nRF5_SDK_for_Thread_and_Zigbee_v4...
Hello Nordic-Team,
I am using the SENSING mechanism on GPIOs to wake up a firmware from SYSTEM OFF. Two GPIOs are used for this and it is crucial for the firmware to detect...
Hi all,
I'm working on BLE time synchronization between nodes using hardware timestamps via GRTC + DPPI + PPIB cross-domain. CRCOK and PHYEND work perfectly, but adding...
HI,
I'm reading this post about NFC antenna matching. It says in Method 1 to connect the coil antenna to the S11 port of the network analyzer. How should I make the connection...
Hello.
Are you able to give any specific details around an SDC Assertion with File ID 13 and Line 451 please?
The nRF Connect version is v3.2.4.
I'm trying to isolate...
[This writeup is a work in progress - it was meant to be a quickie, but to write it all down properly exceeded the limits of reasonable working hours. Writing will continue...
I am currently working on a design with the nRF9160, and have a few questions about the DEC0 pin and decoupling for the module in general. I have been considering adding additional...
Hello Nordic Team,
We are currently working with the nRF54LM20B device and would like to understand whether Bluetooth Channel Sounding is supported on this SoC.
Specifically...
I keep seeing this in your documentation:
This functionality is in the process of being deprecated and replaced by Zephyr’s default devicetree-based memory partitioning...
Hi,
I am testing the radio_test (short-range) sample on an nRF54LM20A DK . The test setup is:
Board: nRF54LM20A DK
Sample: peripheral/radio_test (NCS version...
Hello Nordic Team,
I am evaluating the nRF54LM20B physical DK using nRF Connect SDK v3.3.0‑preview2 . In the SDK, only the nrf54lm20apdk board target is available, and BLE...
Hello guys,
Im developing RTLS with DWM3001C and right now Im working on personal tag powered by CR2450. So naturally, power consumption should be as low as possible....
Goal: Create SBOM with correct version numbers, CPE search strings, PURLs, and licenses. Use that to scan and assess vulnerabilities. Platform: NRF Connect SDK 2.9.1 or newer...
Hello, I am working with the following sample project and NRF Connect SDK v3.3.0. (Referenced regarding this topic .) The sample implements DFU with MCUBoot while using the...
HI,
I am developing an NFC application using the nRF54L15 with SDK version 3.2.1, and I am using NDEF for data exchange. However, I have encountered an issue: after the...
