When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
hi support team,
customer reported on problem that one product is ok when in factory, but now is in problem after delivered to office.
i had onsite debug and find out...
We are nRF52840 in one of our products. When we use SYSTEM OFF mode with with hardware design, current consumption is around 3uA but when we use SYSTEM ON mode with RAM retention...
BLE settings:
1) Advertising interval: 500 ms.
2) I am not explicitly turning on the DC-DC regulator; I am using the default settings.
3) Tx payload: 31 bytes.
According...
Dear All:
I have followed the procedure as shown in the following to make a Mesh heartbeat application.
I started with the example of ligtht switch client and server for...
The documentation for CONFIG_MBEDTLS_PEM_CERTIFICATE_FORMAT in nRF Connect SDK says:
By default only DER (binary) format of certificates is supported. Enable this option...
My question is completely wrong (0x2880 is alloc failure, not parsing failure)! Please ignore.
When using the nRF Connect SDK mbedtls implementation to conduct a TLS...
Hi,
For the nRF52840, can we use another pin than P18 to realise the Pin RESET functionnality?
I can write the register NRF_UICR -> PSELRESET with numbers other than the...
Hi Devzone,
I am facing an issue in my application where my device is working as a BLE peripheral advertising for connection. The device stops advertising after connecting...
I'm trying to download and flash an MCUboot image at runtime. All goes well, the image is flashed to the secondary slot, confirmed, and marked for upgrade. The secondary slot...
I use the nrf_dm demo program, when using the nRF52840DK development board, the program can print the log normally.
Then I changed the build configuration to nRF52840Dongle...
Hello,
I have a custom nrf5340 board with a simple firmware flashed on it (turn on red led). My board has a hall sensor as a turn on/off switch (latched). If I connect it...
I used nRF52840 board with SDK 17_1_0 ,
Using FDS I am able to read and write data into flash when nRF52840 board Continuous ON,
But when i Make nRF52840 board Power OFF...
How can I blacklist BT LE channels/frequency from operation? Context: I have the nRF52840 integrated into our product's design. The device is going into an environment where...
I just upgraded my nRF Connect for VSC to 2.6.1 and now am getting these errors:
and
I saw this as well:
but I have CONFIG_DISPLAY =y in the prj.conf....
I have an application running on a custom nRF5340 board that supports simultaneous BLE DFU of the network and application core with MCUBoot. This ticket: seems to indicate...
