Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello,
my application is running without TF-M and I store a password persistently in trusted memory using "psa_import_key()". This works with SDK 2.4.2. After that I made...
Good day! I have a nRF52840 based board that I interfaced with a MEMS microphone (SPH0645) through I2S interfacing. I got to the point where sounds made near the microphone...
Hi, I am developing on NRF5340 chip, using an external Flash memory (AT25SL321) on my custom board. I was previously using vanilla Zephyr version 3.1.0 (everything was working...
Hello，
Why is this error displayed?
00> <error> ble_scan: sd_ble_gap_scan_start returned 0x7 00> 00> <error> app: Fatal error
I use the example in nRF5_SDK_17.1.0_ddde560...
hi，
I want to know how Bluetooth allocates channel resources as a master.
Assuming a Bluetooth master is connected to 8 slaves simultaneously, how does the master allocate...
I am working on a module MS12SF1 which is nrf5340+nrf7002. I set the mac address in the otp by running wifi_radio_ficr_prog otp_write_params command. After restarting the...
On SDK 17.x.0 only
Please Do not judge the quality of SDK based on number of entries here. This thread should be considered as part of Nordic effort to find issues and...
Hello,
The following error occurred when I ran the program. 00> <info> peer_manager_handler: Connection security failed: role: Central, conn_handle: 0x0, procedure: Encryption...
Now using 52840(S140_nrf52_7.2.0 protocol stack, SDK:17.1.0) Bluetooth packet sending found that the packet sending data length is far less than the actual length to be sent...
I am using a module named MS12SF1 which is a nrf7002+nrf5340 combine module. For wifi initialization, qspi is used. As it wasn't working I added spi4 in the nrf5340dk_nrf5340_cpuapp...
Hi Support Team
If we use nRF52840 develop BLE peripheral base on NCS. What is the maximum number of phones can connect nRF52840 at the same time? Many thanks.
Hello, I'm working on the nrf7002dk WiFi station sample. Most of the time, data is sent and received successfully through HTTP using the HTTP PUT function. However, occasionally...
Hi everyone.
For FCC testing we are required to create firmware builds to transmit at the beginning, middle, and end of the BLE spectrum to allow the lab to verify duty...
This happened last month also during debugging of . I could not use my device for the whole month because the quota was gone in minutes.
Now, new month, new quota, I turn...
Hello,
I am trying to run the asset tracker v2.
I have completed the setup steps and configuration.
Can you please let me know what to do ?
I have read that the -128...
