Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I have enabled advertising fast and slow mode. But changing from fast to slow mode is almost at same time. How to configure for changing advertising mode slowly?
The following...
Hello,
I am using the 9160 to send MQTT messages which are received on AWS. I am provisioning the devices by creating a thing on AWS, getting the certificates, and loading...
I have a problem that my nRF52840 Central cannot discover one of the my nRF52840 Peripheral sensor services. With the phone I have no problem. Also other services are detected...
Hi team,
I am using NRF52833 DK with PCA10100 on it and s140 soft device version..
While I am merging the ble_app_uart example with ble_app_multiperipheral example, the...
Hi, I'm currently developing an automatic connection BLE system.
I'm using nRF52840 DK with nRF Connect SDK and S140 SoftDevice.
In fact, there exist already other...
Hi Nordic,
I would like to understand the philosophy behind the nRF9160 DK acting as a debugger. I recover my thinky:91 connecting the 10 pin flat cable from thingy:91...
I was using nrfjprog successfully about a year ago before this evaluation was suspended. When I now try it fails.
```
nrfjprog --log --program build/zephyr/merged.hex...
Hello,
I'm trying to writte a sensordriver for the nuvoton NAU7802 ADC in Zephyr using the drivers/sensor API. Here are the most important (I believe) parts of my code:...
Hello,
I've recently created a custom board based on the NRF52820 which is configured based on the datasheet.
I'm using an NRF52833 DK OB J-Link to program the device...
Hi,
I use the modified version of the USBD example(nRF5_SDK_17.1.0_ddde560\examples\peripheral\usbd) in nRF5 SDK from here . (My development kit is nRF52840DK.)
And I...
Hi, I have configured normal uart, where you send 1 tx_buf and wait for the rx_buf until you get a response. This setup was fine until the logging feature was requested. However...
Hi, I am developing a product using BLE with nrf52832. We are aiming for a BLE communication range of around 1.0m. However, if txpower is set to -20dbm, BLE communication...
Hi,
I found this forum post about the Verizon APN:
https://devzone.nordicsemi.com/f/nordic-q-a/46288/nrf9160-verizon-sim
This implies that I don't have to use "AT...
I want to parse the following JSON { "ver": 3, "mode": "online", "custom": { "apl1": [ "off" ] } }
Tell me about how to parse json and how to write code
The keywords...
