hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
According to the Nordic infocenter here
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcomp_matrix_nrf9160%2FCOMP%2Fnrf9160%2Fnrf9160_operator_certifications.html&cp...
I am using nRF52840DK for working on my application. I use nRF Connect SDK v1.9.1 to run example and build application. I use VS code to build the application. I am working...
HI
Saw the youtude video: https://www.youtube.com/watch?v=dpvNXQiLbh4
For BLE Audio Broadcast mode, could i check how many channels of audio can be broadcasted and selectable...
I'm developing firmware for a custom board developed with the nRF5340. We opted to use RTT as our logging/shell output as opposed to UART thanks to pcb size limitations. I...
Hi,
We are porting some of our old firmware from SDKs <= 17x to nRF Connect SDK.
We have not found a way to access several of the drivers, like pwm_nrfx.c and use functionality...
Hi,
I'm trying to build the nRF5340 Audio sample application for the nRF5340 Audio DK board and get this error message when creating the project:
Any thoughts?
Regards...
I'm trying to migrate from the nRF52832 to the nRF52833 using the same exact code, but the nRF52833 does not go into low power mode. The nRF52832 consumes 100uA with the nRF52833...
Hello, I have successfully connected two NRF5340s using central_uart and peripheral_uart and can send messages to each other. But I don't know how to test the data rate.
I have an implementation that is using a PWM output to drive a LED. It has been observed that when the LED is on in a constant drive state, fixed PWM output train, the LED...
I would like to communicate at a speed of 1ms or 2ms if possible, as I need to make a gaming mouse with as little latency as possible. To achieve this, I plan to use the nRF52840...
Hi Team,
could you please help us how to remove service change characteristic?
Also please share us how to SET PHY as a constant "BLE_GAP_PHY_1MBPS" ?
please suggest...
The following code got NRF_ERROR_INVALID_STATE. What is meaning of NRF_ERROR_INVALID_STATE? And when will NRF_ERROR_INVALID_STATE generated?
err_code = nrf_drv_gpiote_init...
Dears,
The customer wants to know that the Thingy53 evaluation board can calculate the 3-axis acceleration,angular velocity,magnetic field, these 9sets of data into "quaternion...
I want to remap SPI0 pins from default (P26, P27, P28) to another ones (P08, P09, P10) on PCA10040 under nRF Connect SDK. But I stuck into a problem: SPI module seems to work...
Hi,
I just go a question about when to use the nrf_moden_lib_shutdown(). Is it necessary to use in this code case? Since I've used lte_lc_power_off().
Regards,
Elia...
