Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Hi,
Based on previous threads on the matter:
https://devzone.nordicsemi.com/f/nordic-q-a/46565/sdk-15-3-0-missing-bootloader-definitions-for-nrf52832_xxab-qfab
https...
HI
We are using nrf connect sdk.
We understand that when we put the nrf in power down and if any interrupt comes in any gpio than it will reset and wake up.
But my question...
Hello everyone,
im quite new to nrf52.
i m trying to fecth the ADC value on teraterm. but it is not showing the expected output.
please help..
thanx in advance.
Hi,
I am trying to modify the multilink central example to send string to other board.
In the main.c I inserted the uart_init(), uart_event_handle() methods
I added...
While developing a set of C++ tools to simplify configuring and managing BLE on NRF52 chips, I've encountered an error code returned from the advertising module's ble_advertising_start...
Hi, I have several services running in the application. one of them is DFU.
I have to hide / stop DFU service for example when the SOC of the battery is less than 50%. And...
Hi,
I am working on nrF52832 as a gatt peipheral (server)and have a requirement to send 12KB of data over a custom service. I have done the following:
1. Created a custom...
Hi Nordic:
1. Does NRF9160 modem 1.3.1 support CSQ command?
2 Is there a command to get SINR signal?
3. NCSv1.8.0, modem1.3.1 %XRFTEST (AT%XRFTEST=2,1,0,0) Can it can...
Hi,
we're performing an evaluation of using an nRF528xx module with 802.15.4 stack to replace a 3rd-party radio module. There will need to be an AT command protocol for...
Hi i am using nordic nrf52840 chip. and SDK17.1 i am using.
in that under secure bootloader code i am trying to use the nrf_crypto_hash_update() function to calculate...
Hi,
We need to update the firmware of the device through IOS-nRF-Connect-Device-Manager, but the language currently used in our old project is objective-c. IOS-nRF-Connect...
hello ,
We use the nRF9160‘s GPS. We see that the 9160 Thingy use a GPS LNA between the 9160 module and the 9160 GPS antenna?
We want to know, whether we can do...
Hi,
I know that the Bluetooth mesh cannot use long range, but I want to know whether the output power of the node can be controlled to adjust its broadcast range？
Thanks...
hi support team,
for ncs, how to add dir to segger IDE like this one.
for example, like keil IDE separating those two .c into two folder in segger.
Regards,
William...
HI
This is regarding to create a project which supports below peripheral
1. Uart : To interact with Windows application - Working Configured Successfully
2. I2C: for...
