hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hello, I am working on the NRF9160DK and I have an issue with the asset tracker sample. Firstly, I followed the guidelines explained in the video "Unbox and get your Nordic...
hi support team,
i have ESB project for customer, and now i have one fundamental question about RTC cc compare event, i am struggled in this problem.
static __INLINE...
Hi,
I'm working on direction finding with nrf52833dk (my own board latter on) and Nordic antenna matrix. I'm using NCS v1.6.0-rc2 and example Direction fing connectionless...
Hello there,
I'm facing inconsistency across two nrf51 PCB boards in term of sending the device name. I'm running the same exact code on both. One is advertising the device...
As shown in the provided picture, the download worked after connecting, but the function does not work.
I have checked the following. 1. Check the operation status of...
Hi,
there are couple of examples on NCS with edge impulse. I would like to know how much space edge impulse add to the application, and to see if it can fit into nRF52840...
I have a customer that is using the nRF9160 embedded into their own device. Need to know if the nRF9160 is a module in which case the customer's end device will need to be...
I have written a string data from peer device, and i want to update the device name with the string in run time without resetting the SOC, how can I do it and what are the...
Hello
I am using HTTP to requests on the server with NB-IoT network on NRF9160 chip
I found that in the HTTP REQUEST command with 1 REV () function to get the results...
Hi Nordic,
I've implemented an extension of the NRF DFU protocol using the "external-app" type. The transfer is stored in external flash, and can be approx 1MB in size....
Hi
I have tested direction finding examples successfully., by default parameters. Theses projects are used as "TX" and "RX" in AoA mode:
https://developer.nordicsemi...
Hello, following this question - https://devzone.nordicsemi.com/f/nordic-q-a/76417/saadc-tasks_calibrateoffset-shall-only-be-used-before-tasks_start-or-after-events_end-nrf52833...
How i'm supposed to check if the device is transmiting any data? I used nRF52833 DK as a sink and node of wirepas mesh network, added another DK and configured it as a regular...
Hi,
I'm making an firmware for the nrf52840 that communicate throw usb to a computer.
First I used the uart library that works fine but required the Jtag and Jling which...
