Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi,
I was wondering what example to use if I have an accelerometer on a breadboard connected to the nRF52840 DK via TWI/SPI and the DK connected via USB to my Mac? I want...
Hey guys,
I want to start developing using NRF51822 but I don't know how to start. I have read punch of stuff about BLE but I am not sure how it's works or how to program...
Hi Team,
I am experimenting with the semi-official ble_app_uart_relay example on an nRF52832 DK:
https://github.com/NordicPlayground/nrf52-ble-app-uart-relay
The main...
We are using one of the nRF52 series micro's. It has 12 bits of ADC. My customer is asking can we go to 16 bits of ADC. Can you suggest some products so I can review the specifications...
Hi all.
I want to run the NRF52 dev kit as an HID keyboard, and I've got that working nicely thanks to the keyboard BLE peripheral in the SDK samples, but I also want to...
i am transferriing data between pc and nrf52 dk using nrf libuarte async tx. only the first 5 bytes are sent correctly. after 5 bytes the rest is corrupted. I am trying to...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi all,
Project description and what works:
in my project I have one nRF52840DK as central and three nRF52DK as peripheral. The code on the central is based on the " nrf52...
Hello,
I stumbled over the following problem in configuring an nrf connect sdk project: Somehow I must have dreamt that the Nrf52 UARTs support also baud rates beyond 1mbps...
Hi, I am looking to implement Azure IoT Hub and Azure FOTA in a project. Unfortunately these examples are specifically for the nRF9160. I would like to implement it on the...
I am currently trying to connect an accelerometer to my Nordic board, but I am having some issues with #define NRFX_TWI_INSTANCE(id)
.p_twi = NRFX_CONCAT_2(NRF_TWI, id)...
My problem is with examples of publishing and subscribing at the same time. I crossed them by adding a check for subscription if I did not sign I do this and register the...
Hi guys. I'm fairly new at embedded development and I'm basically trying to set up a workflow that goes like this:
Toggle a GPIO high - low, with a duty cycle of ~500...
I have been following the "Getting started with Nordic's Secure DFU bootloader, a step by step guide". I believe I may have compiled and loaded a DFU bootloader to the nRF52840...
