Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
We use nRF52832 and SDK 17.0.2 and the buttonless secure bootloader without bonding. I don’t understand the below issue, does that apply to our solution ? There will be custom...
I have developed a BLE app on a nRF52382 which advertised those service UUIDs
and set the appearance to BLE_APPEARANCE_CYCLING_POWER_SENSOR which is 1156.
When I...
I am working on a project where I have to store the incoming UART data over BLE on the NRF52840. I am using fstorage library to store the data in flash but I am not able to...
Hi,
I have a PCA10040 DK and am trying to measure current drawn for a non-connectable beacon. After following the instructions in the infocenter about how to do current...
Hi!
This is Cemal from Turkey.
I'm new to this community and for nordic nrf. First of all, I wish everyone a good work.
I've just started a new job at a new company...
My company produces smart helmets and our products have always been using nRF5 v11 SDK on nRF52 chips for almost 5 years now. The latest nRF5 SDK is already on v17 https:...
Hello there,
I am trying to send an add_group_request to a device on the network, and want to capture the send status of the device to check the status of the call. I am...
Hello,
I have been testing out the Power Profiler Kit on an nrf52840 DK (board revision 1.1.0) with the blinky example (SDK 3.2). All is working well and I am able to plot...
Hi Team, Using the nrfconnect for mobile application. Where it is connecting to the BLE device. As every time connecting the MAC address of the mobile is changing, I know...
Dear Sir / Ma'am ,
I am trying to load my simple I2C program on board nrf52840dk. But unfortunately after some time on board LED5 can't turned on and COM PORT not detected...
Hi,
I use nrf52832 with SO 6.0.0 and SDK 15 connected with and IOS 14.2 (iphone XSmax)
some time (about 1 time on 400 connection) in the first packets exchanged after...
Hi ,
I'm working on nrf52833, s113.
I have trouble to secure my system. It has no kayboard or screen, and with 6digit fixd pathkey( no other choice).
That's mean it...
hi there, I have a problem with updating the firmware when the PPK is attached to the nRF52 DK.
I could upload a new version of firmware on the nrf52, but it loads the previous...
