Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi Everyone!
nrf_serial.c and nrf_serial.h are gone in SDK 17.0.2. There are present in 16.0.0. I do not see any mention of this in the release notes.
Was this module...
i am using example code ble_uart for controlling gpio(led & buzzer) by editing bluetooth data handler. I am driving a buzzer using pwm.
led working fine i.e turned on/off...
In nRF Connect SDK I see drivers for BH1749 sensor from Thingy 91, but not for BH1745 from Thingy 52.
Is it possible that the BH1745 sensor will be supported soon? Looks...
I tryed to use the pynrfprog with a Segger-ARM-Flasher to update modem DFU.
I changed the python skript to follow - because there are 2 Segger-ARM-Flasher installed in...
Hi,
When I connect my device to an external power supply, it restarts randomly. It sometimes happens once every minute, sometimes once every 10 minutes. I couldn't find...
Hello,
I am transmitting 1 byte BLE data across a central and peripheral and the central does other things like control PWM, sample SAADC (scan mode), GPIO pins interrupts...
Hello,
When I am loading my project into SES I get the following warning message.
CMake Warning at C:/Zypher/v1.5.0-rc1/zephyr/CMakeLists.txt:1354 (message):
WARNING...
I have a nRF9160DK board and a want to generate a simple interrupt when I press button 1 (pin 6) on the DK board. When this works I will move to a different GPIO and hook...
I'm developing a small function that split string using delimiter (,) but i can't use strtok (undeclared function error)
so i added (CONFIG_NEWLIB_LIBC=y) to prj.conf file...
nRF52 DK fresh out of the box isn't recognized by my Windows 10 PC. When I plug the device into the USB port LED 1 pulses and LED 5 blinks rapidly. However, there is no sound...
when I call nrf_gzll_add_packet_to_tx_fifo after I recive a nrf_gzll_host_rx_data_ready() I get a Error 33542
how can I see what type of error that is?
I was hoping...
Hi
I have a custom-designed board based on nrf52840 and on that board, I am using NFC pins as GPIO.
On Pin no 0.9 and 0.10, output peripherals are connected.
I have...
I updated my Power Profiler software on the NRF Connect Desktop software.
Immediately after switching to the new GUI, I noticed a significant change in power performance...
I am trying to use the NRFX_WDT design in SDK 16.0.0 on a board using the nRF52832.
In the file nrfx_wdt.c, the allocation index is declared/defined as:
static uint8_t...
The drop down does not list the nrf5340dk.
Using nRF Connect Toolchain Manager I open a command prompt in the v1.5.0 sdk,
cd zephyr\samples\drivers\spi_flash
I did:...
