Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
The nRF9160 DK has an I/O expander that can optionally be used to interface the LEDs, slide switches, and buttons.
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrf91_dk...
I want to send sensor data over nrF Mesh using sensor example from Mesh SDK. However, I found that the values over 256 in decimal are not received by the client. What changes...
Hi,
My bootloader and application work good, I take example from SDK 12. The DFU work correctly but at the end my DK stay in bootloader mode and don't reset to start the...
Goodmorning,
I'm working on a project running on nrf840. I would like to add a speech recognition system able to recognize some words ( more or less 10 words).
There...
Hi,
I'm trying to get the current epoch Unix timestamp (or the number of seconds since 01, January, 1970).
I'm using the date_time.h library as Carl Richard suggested...
Hi,
I wish to combine nRF Connect IPSP sample project for nRF52 DK (v1.4.2\zephyr\samples\bluetooth\ipsp) and add MQTT on top of 6lowpan. If yes, any guidance to change...
I have a 9160 project, users hope to display on the screen as soon as possible in the boot of operators NB signal value, actual test when I found this problem, on the product...
Hi, can you assist please....
I am using the Hrs example in SDK 17.0.2 as the basis for an application.
Using an unmodified code by loading the supplied hex file ble_app_hrs_pca10040_s132...
Hi, I'm using nRF52 DK (nRF52832) to detect my sensor. The sensor I2C address is 0x21 (verified by Arduino UNO).
My nRF52 DK (master) could detect the slave sensor before...
Hi,
nRF9160 examples in NCS, the MQTT publish payload now with a pre allocated buffer, is it possible to support streaming payload to save memory usage for large payload...
Hi
I need to know the RSSI but I don´t know how do that, I have a nRF9160DK kit with onboard gps antenna and I have proved the gps sample but it don't show information about...
Hi,
I have a custom PCB with the nrf9610. I have confirmed that https over LTE works fine. I want to enable agps, so I need to get nrfcloud connected.
I made a new device...
I'm developing an audio application which requires Bluetooth connectivity, using an nRF52833. Bluetooth will only be used for control, not for streaming audio in any way....
