Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
HI all,
Recenly, I am playing with nrf5340-DK to do some experiments. I read the datasheet of nrf5340 and found out that L31 is the pin for single-ended antenna connection...
Hello,
I received the Thingy not too long ago. Now that I've run some samples, it's time to use the NB network. I flash the AT_cmd sample. I open LTE Link Monitor to see...
I am designing a custom board for the NRF9160 following the 91 thingy as reference.
I will operate only in US and Canada. I noticed that multiple matching circuits have...
Using ncs v1.4.0, modem FW v1.2.3, SES v5.10d. The code is based on the Asset Tracker, LTE with PSM, motion-activated GPS, using MQTT to send GPS location to backend.
prj...
We are trying to upload Bootloader only, but it fails with 'Error 5: FW version check failed'. Please view log / pictures.
We have tried to change the bootloader version...
Hello,
there is the following page:
https://github.com/NordicSemiconductor/IOS-Pods-DFU-Library/blob/master/documentation.md
Known issues
Since iOS 13.3 (?)...
Hi all. I've seen a few posts about this, but none of them seem to have the knowledge I'm looking for. I am helping plan a device that has two units and will connect to a...
Hi, guys.
I'm using nRF52 DK (PCA10040) and 16x2 LCD ( ST7032i ). I would like to create a custom icon (e.g. degree Celsus ℃). Here is my code. It doesn't print anything...
Hi,
I would like a solution for encrypted OTA firmware update and I just realized that the Secure DFU doesn't enrypt the firmware image just sign it.
I find this Q&A:...
Is there a way to change the Thread SDK example program (\examples\thread\ncp\ftd\uart) baud from 115200 to a higher 460800? If so, what steps are needed to make this change...
With SDK For Mesh v5.0.0 the replay cache is saved to flash using MESH_CONFIG_STRATEGY_ON_POWER_DOWN. In mesh_config_load() a check is made to ensure that there is enough...
Hi,
I'm working on porting BG95 to nrf52 sdk, it'd be a lot helpful if I can get a head start with some open source implementation(AT parser libraries, drivers porting etc...
Hi,
In the Product Specification for nrf52840 it´s written that setting CONFIG (0x50C) register to Pause (0) would pause the watchdog while the cpu is halted by a debugger...
nrf52840 with SDK15
I am trying to update 3 characteristics if the correct value is written to an authenticated read write characteristic. Actually all of my characteristics...
