Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hello
I am building a code with Openthread (NCS V1.4.0) and the size of that generated Bin file is 405kB. I would like to know why size of that file is more? I need to reduced...
Hi!
We are working with the nrf5340 on a custom board and we are trying to reduce its power consumption to the minimum possible. We have a beacon advertisement application...
Hi all,
I have just some issues with sd_flash_write and sd_flash_page_erase functions. I have created some code to read the temperature value and save this value in memory...
Hi,
I am considering nRF52 (most likely nRF52833 or 811 ) for a new design - curious how mature is the concurrent multiprotocol support in nRF52 - in particular for nRF52833...
Hi All,
We are using nRF52840 MCU and SDK nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71. We are designing a device that uses switches connected to the below pins,
Pin...
Hi,
I use a custom board, softdevice and boot loader.
I use DFU to update a slave chip firmware. Everything goes right until we invalidate and write flash :
// Invalidate...
Hi
i use sdk 17.02
custom board
soft device
when i program input digital pin I have an extra consumption of arounf 9µA versus not using it.
Could you tell me if...
Hello,
I am using FDS successfully with SDK 17.0.2, secure bootloader and softdevice. Bluetooth (BLE) environment, if it does matter.
I can read and write data. But following...
hi guys
i develop mobile app for iOS and use nrfMesh lib v3.0-beta1. i have few nodes subscribed to a group. I send GenericLevelSet message to a group and receive successful...
if a response to the http request is chunked ( https://en.wikipedia.org/wiki/Chunked_transfer_encoding ), it is not handled correctly by the serial_lte_modem.
Sometimes...
This should not be so hard - have to go here and wait until this gets answered.
1. I can't find an SDK consistent with SoftDevice s110.
2. I have an nRF51822 production...
I want to find out BLE throughput.
Throughput_bps = num_packets * (ATT_MTU - 3) * 8 / seconds.
In this equation, how can I find out num_packets?
Also, ATT_MTU =...
Hello,
I was just wondering that if somehow we can send the AGPS code data of thingy 91 to adafruit server through the MQTT just for testing purposes.
Let me know...
Hi everybody,
I have some trouble fixing the ERROR 19 [NRF_ERROR_RESOURCES]. I think it's something about the buffer queue size that is too busy. But I don't know how to...
