hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
The system has an nRF52840 as a BLE USB Dongle plugged to a PC, and connected by BLE to another device (another nRF52840).
I measure the latency time between the...
Hello everyone.
I made my own board with nrf2840 and wanted to use the CC310 module for encryption.
I uploaded an example from the SDK to my board and in the debug I see...
Hi,
I am a newbie to nRF devices. I have different sensors connected to TWI,SPI,ADC etc. and need to send these data to a cellphone through BLE. Does anyone has a sample...
Hello,
I'm starting to investigate using the nRF52833 as part of my design and i wanted to clarify the specification in the datasheet. it states the following:
Does...
Hi,
When upgrading a project from ncs 1.3.0 to 1.4.0, the clock_control_on() call behaves different; It always returns -EPERM. Did the API change?
The call is used as...
Hi everyone,
I want to modify the USBD example.
In the USBD example there's a mouse but I don't have to work with a mouse.
I want to transfer data from ADC to PC. How...
Hi, I am using the Nordic nRF52832, with v15.2 of theSDK, and would like to use "nrf_sdh_freertos_init" to implement multilink. I refer to example "ble_app_multilink_central...
I have beacon (ble_app_beacon) transmitting every 40...50 ms, nRFConnect shows adv interval is ~44 ms, so it receives ~22 msg/sec. My beacon listener gets only 10...12 msg...
Hi,
I have simple test firmware that simply connects to the network and goes into PSM sleep, it works perfectly well on the nRF9160DK but the Thingy 91 is refusing to connect...
This is a really basic question, but please bear with me. This is my first time foraying beyond the world of Arduino! :)
I'm attempting to make an ANT+ bicycle power meter...
I am using nrf52832,I have Defigned "CONFIG_NFCT_PINS_AS_GPIOS"as below。P0.09 is configed as POWER_HOLD pin, P0.10 is configed as buton.
I found that when I download softdevice...
Dear Members,
For scanning GSC10 sensor,
can this example be used ?
https://infocenter.nordicsemi.com/topic/sdk_nrf5_v17.0.2/ant_examples_scanning.html
Thanks
Hi,
I am currently working on the project that involves Pre-certified Bluetooth Module (SG Wireless SGW1110 CE & FCC certified, based on Nordic Semiconductor nRF52480)....
I am getting an intermittent "Softdevice assert: 151994:0" error on device initialisation or after the device has run for a period of time. I am using Light Switch Client...
