Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi everyone,
I suppose this is a very simple question... I want to create multiple timers using the Timer Library .
Each time I want to create a new timer based on RTC1...
Hello,
I'm flashing custom code onto a nRF52840 based PCB.
I'm using SDK v15.0, SES 4.52.
On the debug window I get the following message as soon as I run the code...
Hi,
I am using nRF52840, S140 V7.0.1.
I am using Secure Serial Bootloader and able to do DFU of Application.
DFU of application
Using below command able to generate...
Hi,
I have a custom board with nrf52833 I would like to flash with custom firmware. I would like to flash this board by "P19 debug out connector" from DK.
How can I...
I am trying to port a tested program from NRF52 DK to NRF Thingy. To do the same I had changed the board to PCA20020. After I do that, I program using the NRF52 debug out...
Hi,
If the app keeps sending data at a certain rate, the numbers will skip and the software will stop.
I tried to see how much data I could communicate and at what speed...
In my situation, I want to use ble to designed a piconet which has 1 master and up to 4 slave .( upload(Slave->Master) rate is 2.2KB/s,download(Master->Slave) rate is 500...
Hi
A few questions regarding the "saadc_pca10040" example:
If I read one analog pin then what is the meaning of this matrix of values :
"static nrf_saadc_value_t...
This page shows that MPU is not supported on nRF52840: https://infocenter.nordicsemi.com/topic/sdk_nrf5_v16.0.0/nrfx_drv_supp_matrix.html
On the other hand, the following...
Hello Nordic Experts,
I'd like to add the usb hid composite to one of BLE examples. I followed link below and combined the example usbd_hid_composite with ble_app_blinki_c...
Daer usually we need minutes to lock the LTE cell and connect to the network. There is a way after the connection to save the data (NVM or flash) and on restart to use them...
Hello Everyone,
I am trying to implement fds in nrf52832 with sdk 15.2. getting some issues. I am using 5 record key's and 1 file id.
Before coming to that, Can anyone...
Hello Everyone,
I am using nrf52832 and sdk 15.2 for ota over serial. I have made bootloader for OTA over UART and tested same with nrfutil using my dfu package file. firmware...
Hi. I my embedded code I read default MAC address internally and mine is read as 73:7F:..... but in reality is supposed to be F3:7F.....
I have read few tickets where people...
Hello,
We are designing a custom board, and we would like to use an external crystal for the low frequency clock source, but we are running into disconnect issues. A similar...
