Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hello,
I work on a zephyr project with the MCUBoot and two updatable images: custom firmware loader + TFM and main application. Update works over BLE. For testing I use...
Hi
I am planning to develop a product based on the nRF5340 DK.
Please provide a response to the following inquiries:
1. Is it possible to obtain the schematic and PCB...
Hello
I want to clarify something because there seems to be a lot of conflicting information on Dev Zone, and the nRF5340 DK documentation doesn't specify the following...
Hi DevZone,
I am currently working on a project that uses MCUboot (DFU over BLE) on the CPUAPP core together with a custom FLPR application.
I successfully got this working...
Dear Community, Hopefully an easy one: Is there anyway to make the flash programmer selection stick in nRF Connect for VS Code? Every-time I click on Flash to program a device...
I am using ncs v3.3.0, and since Partition Manager will be deprecated, I followed the migration guide to use DTS board configuration. I am using mcuboot in firmware loader...
Using:
NRF9151
TF-M enabled
NCS 3.2.2
I'm trying to find more space for my heap on the nrf9151 and I'm disappointed that with a minimal implementation of TF-M...
I ran into a couple issues with network core updates on NRF5340 when updating from 3.1.0 to 3.4.0 SDK. Problem 1) Network core updates are not backwards compatible with 3...
Hello, We have a question about the errata workarounds applied in SystemInit() in nRF5 SDK v16.0.0. Our firmware is split into two images: a boot application and a main application...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I have a pin on port 1 of the nrf54l15 that I am bitbanging for a custom tx/rx 2-wire protocol. I have already managed to implement the tx capability and I was hoping...
I'm using nrf9151 and trying to upgrade from ncs3.2 to ncs 3.4. I have two builds, one with log disabled, other with rtt logging enabled. Both builds are working, but I can...
Hi Nordic Team,
I am using MCUBoot with BLE DFU on nRF5340 and I am facing an issue where the DFU process cannot complete due to my application’s custom boot logic.
After...
