Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
nRF91 repeatedly transitions to `+CEREG: 4` approximately every five minutes while roaming on Vodafone Germany
## setup
nrf9151 modem FW: mfw_nrf91x1_2.0.4
current SDK...
SDK: nRF Connect SDK v3.4.0 (TF-M v2.3.0) Board: nRF9151 (seen on both nrf9151dk and a custom nRF9151 board) Config: CONFIG_TFM_PROFILE_TYPE_MINIMAL=y, MCUboot with CONFIG_USE_SEGGER_RTT...
While building the program I get this error message: "DT_N_NODELABEL_cpucell_cpuapp_ipc_shm_trace_REG_IDX_0_VAL_ADDRESSU" As far as I can tell, this error message is releated...
HI ,
I wan to disable the vBus "VBUS is not valid, and the pull-up resistor on D+ is disabled." on nRF54LM20,
I try to write to disconnect usb from PC :
NRF_USBHS...
Hello, In the latest nRF Connect SDK 3.2. , I've been having a few "sysbuild/mcuboot/boards" folder layout issues with nRF54L15DK / nRF5340DK when using external device FLASH...
I'm running into a similar issue to Case ID 304027 with trying to build the nRF Thread coprocessor project for the nRF5340. I'm able to compile the coprocessor project just...
Dear Nordic Team,
I am working on implementing OTA (Over-The-Air) firmware updates over UART on the nRF54L15 platform. I have been following the "Exercise 1 - DFU over UART...
I am writing regarding an issue I am experiencing with two MDBT53V-1M modules (nRF5340) that I have assembled on custom PCBs. Both modules exhibit identical behavior, which...
NCS has a sample showing sending UDP packets over a cellular network, with optional control over the RAI socket options:
https://nrfconnectdocs.nordicsemi.com/ncs/latest...
Hello,
I am debugging a custom board that uses an nRF7002 connected to an nRF54L15. The nRF7002 power-up sequence appears to be working correctly, but the device does not...
Summary: CONFIG_MBEDTLS is force-enabled and won't compile without PSA_CRYPTO, costing ~31 KB of secure RAM for unused functionality
I've just migrated my project from v...
Hello,
I am trying to debug a basic test project and using the "Debug with Ozone" button in the nRF Connect for VS Code extension. I am using the nrf54l15dk board for development...
When compiling some USB code, my compiler spits out this error:
../../SDK/15.3.0/components/libraries/usbd/class/hid/generic/app_usbd_hid_generic.c: In function 'app_usbd_hid_generic_idle_report_set...
