When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hello! I am having issues dfu from the huawei p30 lite. with nrf51. Tried with nrf connect and nrf toolbox.
Dfu progress stops at 2-3% when uploading. Error Remote dfu error...
I am unable to connect the nRF9160DK to the cellular network.
I have gone through the "Get started guide" (working in Linux) and I have been able to install the SDK. I have...
Hi, we have faced with the same issue as many nRF52 users, debug interface (DIF) will stay active after flashing and high (~3mA) continuous current remains, Power cycle will...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image.
In BLE peripheral example ‘ble_app_template’, it is for doing Advertisement...
hi... folks
I am working on multilink central example, i have modified this example to multi link central uart ,where i can able to connect to multiple peripheral to a single...
Hi,
I am using NRF51822(PCA10028) ble_app_uart example , I need to change the name of the BLE device during Advertising and store the name in Flash so that when ever the...
Hello,
I am trying to establish a network to send data over the boards.
I tried using examples in Ble_central and Ble_peripheral, but in those examples they would stay...
Using the esb tx fifo, it appears to change the ESB_MODE from PTX to PRX, and changes the esb channel to some other value. Is there any way to setup the radio so that it doesn...
Hello,
I am working with nrf52840. I have read how the SAADC example works at https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v13.0.0%2Fnrf_dev_saadc_example...
Hi everyone, I'm having trouble deciding on the "best" / "most sane" way to interface two I2C sensors with the nRF5832. Both sensors are on the same I2C bus. The first sensor...
Hi Bro
I have a project need to use BLE + ESB Concurrently, actually I have did it in my previous project
but seems it has problem in new SDK
In my old project: SDK11...
I'm using the nRF52 DK (with an updated firmware) to program an external target (using the "Debug out" connector). It looks like the programming speed is limited to 1MHz:...
HI,
I am seeking help in getting the only peripheral code from the ble_app_mtu_throughput. Actually, I want to use the only peripheral code in my and want to use the maximum...
I have multiple sensors. I would like to ask if there is support for linking 4 or even 4 Bluetooth devices at a time.
My ultimate goal is to connect 4 or more Bluetooth...
