Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
I'm developing an application for the nRF52832 using the nRF5 SDK version 15.0.0. We're using the s132 softdevice, the sample secure bootloader (modified to use our company...
Hi, I have been running into a problem where I am getting inconsistently failure to start advertising.
Calling:
err_code = ble_advertising_start(&m_advertising, BLE_ADV_MODE_FAST...
Hello, I'm trying to write code to a custom PCB with a nRF52832 using the nRF52 DK and the following wiring:
However, everytime I try to connect the JLink is says...
I'm fairly new to working this close to hardware and am playing around with a few things. I'm trying to bit bang i2c over a couple of gpio lines and everything seems to be...
1.Does nRF52840 and nRF9160 have conformal shielding in manufacture procedure？
2.Do i need reserve shield cover for these two module when I develop product？
Hello,
I'm having trouble adapting my code which works for reading the MAX30100 sensor using TWI input with the NRF51 DK kit.
I would like to adapt this code to be used...
Hello, I am at a loss because this question has come up several times in your forums and the solution is not working for me. Every time I run my program I am receiving a NRF_ERROR_NO_MEM...
I have a nrf9160dk and I setup the whole tool chain by following the Getting Started Assistant. I can't figure out how to connect to the board. Probably just a simple switch...
We are in the final stages of product development and are planning to enter the first batch of production by the end of January. We have a custom board tested, software written...
Installed nRF5_SDK_15.2.0_9412b96 to use with the nRF528240 DK. The SPI example suggests using a makefile. My computer does not have "make", nor gcc. Did I need to install...
Hi all,
I would like to know if there is a way to use the NRF52180 as a central scanning device. I searched for central examples in sdk 14.x.x and 15.x.x but they have central...
HI,
I am using sdk 12.2.2 and nrf52. I have write characteristics in my beacon but I can only send 20 bytes in one write cycle. How can I send more than 20 bytes?
Hello all,
Would it be possible to do a simple model that has a 3-condition switching state to control Forward/Backward/Stop conditions? I am looking to implement this...
