Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello! We are trying to transfer the data between two nRF52840 development kits through NFC. Is doing so possible without using any other reader hardware? If not, then we...
I am using SDK13 with a nRF52832 development board.
When trying to compile the Multilink central example with gcc and I am getting the following error:
../../../../.....
I'm just a bit confused on how gpio detect works. After setting the sense config for input I realize that a change in voltage will trigger a sense signal that will create...
I mange to identify and provision the Light switch example on the PCA10059 Dongle and fanstel gateway with no problems. IT use to work on my PCA10056 DK but has for some reason...
I am using nRF52 SDK v15.2.0, nRF SDK Mesh 3.0.0, and Segger v4.1.2.
I am trying to add the proxy service to the client node of the BLE_UART_COEXIST example. Has anyone...
Hello all
i have problem with doing this example
https://github.com/gamnes/nRF52832-buttonless-dfu-development-tutorial
Here is my stepts to do this
1.Download Sdk...
Hello
We start working with Zephyr and nrf52840. What is the right way to overwrite values defined in nrfx_config_nrf52840.h with Zephyr? The NRFX_CLOCK_CONFIG_LF_SRC is...
I was wondering what determines the logic level of the nRF52840 interfaces? Is it whatever you supply VDD with?
For example, if I supply VDD with 2.8V, will the logic...
I need to port a system from a STM32F407 MCU to the nrf52832.
The old system would continuously poll a SPI slave for 244 bytes of information and after receiving 60 valid...
Hi,
I am working on the ADC and trying to sense the battery level to measure it voltage.
And I have configure the ADC with normal conditions as present in example of SDK...
Hello
First things first, when I use the UART example located in:
\nRF5_SDK_15.2.0_9412b96\examples\peripheral\uart\pca10040\blank\ses
all works fine, the script compiles...
Hi,
I hope this is the correct place to ask beginner questions. I new to microcontrollers in general.
So first of all here is what I am using currently:
Software:
...
Hi,
I'm using Nrf52 with SDX 15.2.
The device is far for the host (smartphone), I would like to know if I can know the RSSI with the Smartphone? How can I control the...
