Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
static void onoff_state_value_update(app_onoff_server_t * p_server) { /* Requirement: If delay and transition time is zero, current state changes to the target state. */ if...
My app (using S130v2.0.1 nRF51822 SDK12.3) triggers app_error_fault_handler (seen on a PIN; since not able to debug due to timing) on sd_softdevice_disable(). A snippet of...
Hi,
I am using nRF5_SDK_12.3.0 and based on \ble_peripheral\ble_app_uart ( with softdevice of s130) to build my application.
Recently, I tried to add the wdt to my nrf51822...
I adapted the light switch demo of the nRF5 SDK for Mesh for sending a series of reliable on/off messages sequentially from an nRF52840 Preview DK to 20 Thingy:52 servers...
Hi. I have set up a nine node mesh using Thread and the nRF52840 chips. I am using the COAP example. All my nodes are visible and i am able to send pings between them. I am...
Hello I have the dk board and am hoping there is some example or tutorial to help me get started with my project. My goal is to use the nRF52840 as a master to multiple devices...
I have modified it so that it works with two nRF51 DKs, one acting as a central and other acting as a peripheral.
The base UUID for this service by default is
{0x9E...
Hello,
First, my setup:
nRF52840 Dongle
Softdevice S140 6.1
SDK 15.2
I built my own adapted application code based on the multilink central example and managed...
I am new to the Nordic chips and for my project I am using an NRF5832 module from Accono. My question is how to get the free SES license for Nordic? When i go to license.segger...
Hello~
I have finished a few easy peripheral project.
Now I tried to understand the structure of central example, ex: ble_hrs_c, ble_nus_c....
I found that services...
When I print too much information ，RTT lost some thing
when I enable the “NRF_LOG_BACKEND_SERIAL_USES_UART”，It is ok
Who tell me Why？ any help will be appreciate！
Hi Nordic,
A problem was found with the SDK15.2 write operation. If the write size is equal to 12000 bytes, the system will return an invalid operation length error.
But...
Hello,
During development with the Mesh SDK, we realized that it would not be possible to use a vast number of functions, even those relating to message publishing, without...
