Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
What this ticket reports
We ship a battery-powered nRF5340 product using the nRF Connect SDK's documented production security configuration: immutable bootloader (NSIB/b0...
Hello,
I have been a Nordic DevZone member for several years, but I have never published a blog post.
I would now like to contribute a technical article about an open...
Hello Nordic Support Team,
I am working on a project using the nRF54LM20B controller, and my application requires operation in a very low-power mode .
To optimize...
Hi,
I've been developing the next version of our product with an nRF54L15 There's external SPI flash attached on QSPI via SQSPI which is working ok (albeit it is very slow...
Hello,
I am trying to understand how the documented tRXCHAIN value relates to the timing of EVENTS_ADDRESS in BLE 1M mode.
In this DevZone ticket:
https://devzone.nordicsemi...
Hi DevZone! I'm migrating an app running on a Thingy91 from SDK 2.5.0 to 3.4.0. I will eventually try to adapt it to the newest Thingy91X. So far I managed to migrate the...
Hi all,
We're building a PoC of a simple BLE device with a following setup:
custom PCB with nrf54l15 rev2 and 32MHz oscillator
FreeRTOS + custom port
nrfx version...
We are observing an unexpected increase in current consumption when enabling the LED driver outputs of the nPM1304.
We configure the LED drivers to Host mode , which by...
Hello Nordic support,
We are preparing a build-only NCS2.9.0 environment on an Apple Silicon Mac, macOS26.5.1 (25F80), with commands run in a managed workspace execution...
Hi, i have downloaded the app nRF for desktop, but when i try to download an app inside it (such as Programmer or Direct Connect) i get notified with this error
i try...
Hi Nordic team,
I am following up on a previous thread ( nRF54L15 sQSPI support for SPI NAND in NCS v3.3.1 ) where it was confirmed that NAND flash was not supported in...
The nRF91 series of modem firmware are distributed with FOTA-TEST diffs to allow for validation of FOTA integrations. Will the nRF93M1 firmware images be distributed with...
NCS SDK 3.4.0 NRF54LM20DK
The nRF54LM20A data sheet warns against using the same RAM subordinate by more than one bus manager. From section 4.2.1,
Avoid situations where...
