Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi. I'm working on a code that performs an action and immediately goes into System OFF mode. Before that, it configures GRTC as a wake-up source with a 5 secs timeout. I've...
Hello, I designed a new custom PCB with nRF52832 and I would like to ask you for verification.
I have the MCU and some components regarding Battery Management.
The idea...
Hello,
in my application I use SPI communication to control my display. For that I have configured the pins for spi4 in the dts and all works fine.
Now I would like...
Question:
What's the maximum NRF_SDH_BLE_GATT_MAX_MTU_SIZE supported by S113 v7.2.0 on nRF52833?
Current setup:
Chip: nRF52833
SoftDevice: S113 v7.2.0
...
I am following the nRF Connect SDK Academy, Lesson 1, Exercise 2 on a Windows 11 system. I got to step 4.12, "Click the build configuration button." After running for some...
Hello,
The MPLAB Snap debugger says that it supports "Cortex SWD". Can I use this to program an NRF54L15? Ideally I'd build the program in nordic vs code and then take...
Hello team,
I am using SPI00 of NRF54L15 to communicate with w25q32fv (spi Flash). I am using a custom board. Below is the configuration I set in .overlay file
And below...
We would like to reset or factory reset or initial flashing of nrf52840dk? We tried pressing RESET button during power cycle, but did not worked. Let us know your thoughts...
Hi,
I'm designing a battery-powered device using the nPM1304 PMIC and nRF54L15. I want to implement a sleep/wake function using a single button.
Desired behavior:
...
This has been resolved, but resolving this issue took quite a bit effort: I was wondering why my NFC was not working on my custom board. First I thought it would be an antenna...
Hi Nordic Support,
I’m designing a product with the nPM2100 using NiMH batteries .
I know the fuel gauge feature is designed for primary cells and lacks hardware coulomb...
Hi,
The Bluetooth Channel Sounding specification empowers every compatible device (like the new nRF54L series devices) to be a mini radar actually. The Bluetooth Channel...
Hi,
Our team is considering the use of SiTime MEMS oscillators, namely a SiTime SiT1615B, to help in harsh shock and vibration conditions our product will be used in....
Hi, I am using the nRF52840 DK with SDK 17.0.2.
I am working on a project using the ESB protocol. In my design, an ACK packet is transmitted to the receiver every 5 seconds...
