Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Yesterday I want to demonstrate the installed toolchain using the nRF Connect for Desktop.
I got errors and it seems to be required to have internet connection.
Is that...
I try to run https://github.com/NordicSemiconductor/pc-ble-driver/tree/master/examples/nordic_uart_client But the following error occurred.
D:\pc-ble-driver\build\examples...
We do have an eeprom accessed over the SPI, and works well.
Need to add an option to access also the I2C eeprom.
Adding to the project nrf_drv_twi,c, nrfx_twi.c, nrfx_twim...
Hello every one
Pin numbers on DK boards are printed as P0.08 or P1.20 etc. but in nrf_config.h files Nordic assigns numbers to the pins. There are pin numbers from 0 to...
We are developing an application based in nRF5340 using nRF Connect SDK v1.7.0
In this application we have a bootloader for both app and net cores.
Bluetooth is set to...
I am testing UART between PCA10040(nrf52832) and Raspberry Pi 4. I connect TX/RX/GND 3 lines between RPI4 and PCA10040.
On host RPI4 side, my test app send 1 byte to 32...
Hi All,
I just had a quick question about the SDK as it pertains to assigned services. Is the BLE Base UUID defined anywher ein the SDK files? i have looked all over; ble_types...
Segger Studio is capable of reporting Flash usage and Ram usage (heap & stack).
Is there a way to do that without Segger Studio? I'm using gcc, JLink command line tools...
Hello,
I am working on nrf52832 I have set up the SES IDE v 5.5 environment with SDK 17.0.2.
I am getting compilation error "unknown type name 'uint32_t' "
The...
I have a custom model and I successfully configured its publication parameters with bt_mesh_cfg_mod_pub_set_vnd
The model publishes at specified intervals as expected
...
Hi,
I followed this guide to use puncover but failed:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/develop/optimizations/tools.html
I am using...
The Nordic Thingy:91 comes with Bluetooth, and for now most of my deployment will be in areas where I'll be able to connect to it via BLE. I can receive data from my Nordic...
Hi guys,
So here is our application:
we have an external 1GB NAND flash on the board with a nRF52840 SoC. We save sensor inputs to the 1GB flash and when we connect...
